/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2010-2011 Freescale Semiconductor, Inc.
+ * Copyright 2020 NXP
*/
/*
#ifndef __CONFIG_H
#define __CONFIG_H
+#include <linux/stringify.h>
+
#include <asm/config_mpc85xx.h>
-#define CONFIG_NAND_FSL_IFC
#ifdef CONFIG_SDCARD
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SYS_NAND_U_BOOT_SIZE ((768 << 10) - 0x2000)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE)
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS 0
#else
#ifdef CONFIG_TPL_BUILD
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_NAND_INIT
#define CONFIG_SPL_COMMON_INIT_DDR
#define CONFIG_SPL_MAX_SIZE (128 << 10)
-#define CONFIG_TPL_TEXT_BASE 0xD0001000
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
#define CONFIG_SYS_NAND_U_BOOT_SIZE (576 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000)
#define CONFIG_SYS_NAND_U_BOOT_START (0x11000000)
-#define CONFIG_SYS_NAND_U_BOOT_OFFS ((128 + 128) << 10)
#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SPL_INIT_MINIMAL
#define CONFIG_SPL_NAND_MINIMAL
#define CONFIG_SYS_NAND_U_BOOT_SIZE (128 << 10)
#define CONFIG_SYS_NAND_U_BOOT_DST 0xD0000000
#define CONFIG_SYS_NAND_U_BOOT_START 0xD0000000
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (128 << 10)
#endif
#define CONFIG_SPL_PAD_TO 0x20000
#define CONFIG_TPL_PAD_TO 0x20000
#endif
#ifdef CONFIG_TPL_BUILD
-#define CONFIG_SYS_MONITOR_BASE CONFIG_TPL_TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE 0xD0001000
#elif defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
#else
#endif
/* High Level Configuration Options */
-#define CONFIG_SYS_HAS_SERDES /* common SERDES init code */
#if defined(CONFIG_PCI)
#define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */
-#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
-#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
/*
* PCI Windows
* Memory space is mapped 1-1, but I/O space must start from 0.
*/
/* controller 1, Slot 1, tgtid 1, Base address a000 */
-#define CONFIG_SYS_PCIE1_NAME "mini PCIe Slot"
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE1_IO_PHYS 0xfffc00000ull
#else
#endif
/* controller 2, Slot 2, tgtid 2, Base address 9000 */
-#if defined(CONFIG_TARGET_P1010RDB_PA)
-#define CONFIG_SYS_PCIE2_NAME "PCIe Slot"
-#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_SYS_PCIE2_NAME "mini PCIe Slot"
-#endif
#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xc0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc20000000ull
#else
-#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
#endif
-#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000
-#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
#ifdef CONFIG_PHYS_64BIT
#define CONFIG_SYS_PCIE2_IO_PHYS 0xfffc10000ull
#else
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#endif
-#define CONFIG_ENV_OVERWRITE
-
-#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on P1010 RDB */
-#define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for P1010 RDB */
-
#define CONFIG_HWCONFIG
/*
* These can be toggled for performance analysis, otherwise use default.
#define CONFIG_ENABLE_36BIT_PHYS
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x1fffffff
-
/* DDR Setup */
#define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 1
#define SPD_EEPROM_ADDRESS 0x52
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_FLASH_QUIET_TEST
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#undef CONFIG_SYS_FLASH_CHECKSUM
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
| CSOR_NAND_PGS_512 /* Page Size = 512b */ \
| CSOR_NAND_SPRZ_16 /* Spare size = 16 */ \
| CSOR_NAND_PB(32)) /* 32 Pages Per Block */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
#elif defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_SYS_NAND_ONFI_DETECTION
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
| CSOR_NAND_PGS_4K /* Page Size = 4K */ \
| CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
| CSOR_NAND_PB(128)) /*Pages Per Block = 128 */
-#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
#endif
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
/*
* Config the L2 Cache as L2 SRAM
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED 400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
#define I2C_PCA9557_ADDR1 0x18
#define I2C_PCA9557_ADDR2 0x19
#define I2C_PCA9557_BUS_NUM 0
/* I2C EEPROM */
#if defined(CONFIG_TARGET_P1010RDB_PB)
-#define CONFIG_ID_EEPROM
#ifdef CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#endif
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define MAX_NUM_PORTS 9 /* for 128Bytes EEPROM */
#endif
/* enable read and write access to EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* RTC */
#define CONFIG_RTC_PT7C4338
#if defined(CONFIG_HAS_FSL_DR_USB)
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_USB_EHCI_FSL
#endif
#endif
*/
#if defined(CONFIG_SDCARD)
#define CONFIG_FSL_FIXED_MMC_LOCATION
-#define CONFIG_SYS_MMC_ENV_DEV 0
#elif defined(CONFIG_MTD_RAW_NAND)
#ifdef CONFIG_TPL_BUILD
#define SPL_ENV_ADDR (CONFIG_SYS_INIT_L2_ADDR + (160 << 10))
#define CONFIG_LOADS_ECHO /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
#if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI_HCD) \
|| defined(CONFIG_FSL_SATA)
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin/* U-Boot image on TFTP server */
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR 1000000
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=" __stringify(CONFIG_DEF_HWCONFIG) "\0" \
"netdev=eth0\0" \
"i2c mw 19 1 4; i2c mw 19 3 f3; reset\0"
#endif
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs; " \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_RAMBOOTCOMMAND
-
#include <asm/fsl_secure_boot.h>
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff