configs: migrate CONFIG_VIDEO_BMP_RLE8 to defconfigs

[platform/kernel/u-boot.git] / include / configs / MPC8641HPCN.h

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 298fe5a..e6e1e79 100644 (file)
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2006, 2010-2011 Freescale Semiconductor.
  *
  * Srikanth Srinivasan (srikanth.srinivasan@freescale.com)
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -16,16 +15,15 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/stringify.h>
+
 /* High Level Configuration Options */
-#define CONFIG_MP              1       /* support multiple processors */
 #define CONFIG_LINUX_RESET_VEC 0x100   /* Reset vector used by Linux */
-#define CONFIG_ADDR_MAP                1       /* Use addr map */
 
 /*
  * default CCSRBAR is at 0xff700000
  * assume U-Boot is less than 0.5MB
  */
-#define        CONFIG_SYS_TEXT_BASE    0xeff00000
 
 #ifdef RUN_DIAG
 #define CONFIG_SYS_DIAG_ADDR        CONFIG_SYS_FLASH_BASE
@@ -45,12 +43,7 @@
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 
-#define CONFIG_TSEC_ENET               /* tsec ethernet support */
-#define CONFIG_ENV_OVERWRITE
-
 #define CONFIG_BAT_RW          1       /* Use common BAT rw code */
-#define CONFIG_HIGH_BATS       1       /* High BATs supported and enabled */
-#define CONFIG_SYS_NUM_ADDR_MAP 8      /* Number of addr map slots = 8 dbats */
 
 #define CONFIG_ALTIVEC         1
 
@@ -68,9 +61,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CLK_FREQ    get_board_sys_clk(0)
 #endif
 
-#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
-#define CONFIG_SYS_MEMTEST_END         0x00400000
-
 /*
  * With the exception of PCI Memory and Rapid IO, most devices will simply
  * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
@@ -101,7 +91,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * DDR Setup
  */
-#define CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 
@@ -215,8 +204,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000     /* early monitor loc */
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
@@ -230,8 +217,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_SDRAM_SIZE  256
 #endif
 
-#undef CONFIG_CLOCKS_IN_MHZ
-
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 #define CONFIG_SYS_INIT_RAM_ADDR       0x0fd00000      /* Initial RAM address */
@@ -247,7 +232,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_MALLOC_LEN          (1024 * 1024)    /* Reserved for malloc */
 
 /* Serial Port */
-#define CONFIG_CONS_INDEX     1
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK         get_bus_freq(0)
@@ -344,8 +328,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
 
 /************************************************************
  * USB support
@@ -373,23 +355,16 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #undef CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 
-#define CONFIG_SCSI_AHCI
-
 #ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
 #define CONFIG_SATA_ULI5288
 #define CONFIG_SYS_SCSI_MAX_SCSI_ID    4
 #define CONFIG_SYS_SCSI_MAX_LUN        1
 #define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE      CONFIG_SYS_SCSI_MAX_DEVICE
 #endif
 
 #endif /* CONFIG_PCI */
 
 #if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_MII             1       /* MII PHY management */
-
 #define CONFIG_TSEC1           1
 #define CONFIG_TSEC1_NAME      "eTSEC1"
 #define CONFIG_TSEC2           1
@@ -561,14 +536,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * Environment
  */
-#ifndef CONFIG_SYS_RAMBOOT
-    #define CONFIG_ENV_ADDR            \
-                       (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
-    #define CONFIG_ENV_SECT_SIZE               0x10000 /* 64K(one sector) for env */
-#else
-    #define CONFIG_ENV_ADDR            (CONFIG_SYS_MONITOR_BASE - 0x1000)
-#endif
-#define CONFIG_ENV_SIZE                0x2000
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
@@ -577,17 +544,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 
 /*
@@ -613,7 +575,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_IPADDR          192.168.1.100
 
-#define CONFIG_HOSTNAME                unknown
+#define CONFIG_HOSTNAME                "unknown"
 #define CONFIG_ROOTPATH                "/opt/nfsroot"
 #define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       u-boot.bin      /* U-Boot image on TFTP server */