#define CONFIG_MPC86xx 1 /* MPC86xx */
#define CONFIG_MPC8641 1 /* MPC8641 specific */
#define CONFIG_MPC8641HPCN 1 /* MPC8641HPCN board specific */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
+#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
+/*#define CONFIG_PHYS_64BIT 1*/ /* Place devices in 36-bit space */
+#define CONFIG_ADDR_MAP 1 /* Use addr map */
#ifdef RUN_DIAG
-#define CFG_DIAG_ADDR 0xff800000
+#define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE
#endif
-#define CFG_RESET_ADDRESS 0xfff00100
+/*
+ * virtual address to be used for temporary mappings. There
+ * should be 128k free at this VA.
+ */
+#define CONFIG_SYS_SCRATCH_VA 0xe0000000
+/*
+ * set this to enable Rapid IO. PCI and RIO are mutually exclusive
+ */
+/*#define CONFIG_RIO 1*/
+
+#ifndef CONFIG_RIO /* RIO/PCI are mutually exclusive */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */
#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+#endif
#define CONFIG_FSL_LAW 1 /* Use common FSL law init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */
+#define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */
#define CONFIG_ALTIVEC 1
/*
* L2CR setup -- make sure this is right for your board!
*/
-#define CFG_L2
+#define CONFIG_SYS_L2
#define L2_INIT 0
#define L2_ENABLE (L2CR_L2E)
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
-#define CFG_MEMTEST_END 0x00400000
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+
+/*
+ * With the exception of PCI Memory and Rapid IO, most devices will simply
+ * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA
+ * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0.
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f00000000ULL
+#else
+#define CONFIG_SYS_PHYS_ADDR_HIGH 0x0
+#endif
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-
-#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
-#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+
+/* Physical addresses */
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0xf
+#define CONFIG_SYS_CCSRBAR_PHYS (CONFIG_SYS_CCSRBAR_PHYS_LOW \
+ | ((u64)CONFIG_SYS_CCSRBAR_PHYS_HIGH << 32))
+#else
+#define CONFIG_SYS_CCSRBAR_PHYS_HIGH 0x0
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR_PHYS_LOW
+#endif
/*
* DDR Setup
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
-#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
#define CONFIG_VERY_BIG_RAM
-#define MPC86xx_DDR_SDRAM_CLK_CNTL
-
#define CONFIG_NUM_DDR_CONTROLLERS 2
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
/*
* These are used when DDR doesn't use SPD.
*/
-#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
-#define CFG_DDR_CS0_BNDS 0x0000000F
-#define CFG_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
-#define CFG_DDR_TIMING_3 0x00000000
-#define CFG_DDR_TIMING_0 0x00260802
-#define CFG_DDR_TIMING_1 0x39357322
-#define CFG_DDR_TIMING_2 0x14904cc8
-#define CFG_DDR_MODE_1 0x00480432
-#define CFG_DDR_MODE_2 0x00000000
-#define CFG_DDR_INTERVAL 0x06090100
-#define CFG_DDR_DATA_INIT 0xdeadbeef
-#define CFG_DDR_CLK_CTRL 0x03800000
-#define CFG_DDR_OCD_CTRL 0x00000000
-#define CFG_DDR_OCD_STATUS 0x00000000
-#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
-#define CFG_DDR_CONTROL2 0x04400000
-
-/*
- * FIXME: Not used in fixed_sdram function
- */
-#define CFG_DDR_MODE 0x00000022
-#define CFG_DDR_CS1_BNDS 0x00000000
-#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
-#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
-
+#define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */
+#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
+#define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */
+#define CONFIG_SYS_DDR_TIMING_3 0x00000000
+#define CONFIG_SYS_DDR_TIMING_0 0x00260802
+#define CONFIG_SYS_DDR_TIMING_1 0x39357322
+#define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
+#define CONFIG_SYS_DDR_MODE_1 0x00480432
+#define CONFIG_SYS_DDR_MODE_2 0x00000000
+#define CONFIG_SYS_DDR_INTERVAL 0x06090100
+#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
+#define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
+#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
+#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
+#define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
+#define CONFIG_SYS_DDR_CONTROL2 0x04400000
#define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_NXID
+#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_ID_EEPROM
-#define CFG_I2C_EEPROM_ADDR 0x57
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-/*
- * In MPC8641HPCN, allocate 16MB flash spaces at fe000000 and ff000000.
- * There is an 8MB flash. In effect, the addresses from fe000000 to fe7fffff
- * map to fe800000 to ffffffff, and ff000000 to ff7fffff map to ffffffff.
- * However, when u-boot comes up, the flash_init needs hard start addresses
- * to build its info table. For user convenience, the flash addresses is
- * fe800000 and ff800000. That way, u-boot knows where the flash is
- * and the user can download u-boot code from promjet to fef00000, a
- * more intuitive location than fe700000.
- *
- * Note that, on switching the boot location, fef00000 becomes fff00000.
- */
-#define CFG_FLASH_BASE 0xfe800000 /* start of FLASH 32M */
-#define CFG_FLASH_BASE2 0xff800000
-
-#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+#define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */
+#define CONFIG_SYS_FLASH_BASE_PHYS (CONFIG_SYS_FLASH_BASE \
+ | CONFIG_SYS_PHYS_ADDR_HIGH)
-#define CFG_BR0_PRELIM 0xff001001 /* port size 16bit */
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Boot Flash area*/
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
-#define CFG_BR1_PRELIM 0xfe001001 /* port size 16bit */
-#define CFG_OR1_PRELIM 0xff006ff7 /* 16MB Alternate Boot Flash area*/
+#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+ | 0x00001001) /* port size 16bit */
+#define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/
-#define CFG_BR2_PRELIM 0xf8201001 /* port size 16bit */
-#define CFG_OR2_PRELIM 0xfff06ff7 /* 1MB Compact Flash area*/
+#define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \
+ | 0x00001001) /* port size 16bit */
+#define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */
-#define CFG_BR3_PRELIM 0xf8100801 /* port size 8bit */
-#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
+#define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \
+ | 0x00000801) /* port size 8bit */
+#define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/
+/*
+ * The LBC_BASE is the base of the region that contains the PIXIS and the CF.
+ * The PIXIS and CF by themselves aren't large enough to take up the 128k
+ * required for the smallest BAT mapping, so there's a 64k hole.
+ */
+#define CONFIG_SYS_LBC_BASE 0xffde0000
+#define CONFIG_SYS_LBC_BASE_PHYS (CONFIG_SYS_LBC_BASE \
+ | CONFIG_SYS_PHYS_ADDR_HIGH)
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
-#define PIXIS_BASE 0xf8100000 /* PIXIS registers */
+#define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000)
+#define PIXIS_BASE_PHYS (CONFIG_SYS_LBC_BASE_PHYS + 0x00010000)
+#define PIXIS_SIZE 0x00008000 /* 32k */
#define PIXIS_ID 0x0 /* Board ID at offset 0 */
#define PIXIS_VER 0x1 /* Board version at offset 1 */
#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */
+#define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
-#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
+#define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
+
+/* Compact flash shares a BAT with PIXIS; make sure they're contiguous */
+#define CF_BASE (PIXIS_BASE + PIXIS_SIZE)
+#define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE)
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
-#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */
#define CONFIG_FLASH_CFI_DRIVER
-#define CFG_FLASH_CFI
-#define CFG_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_EMPTY_INFO
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CONFIG_SYS_RAMBOOT
#endif
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
#undef CONFIG_SPD_EEPROM
-#define CFG_SDRAM_SIZE 256
+#define CONFIG_SYS_SDRAM_SIZE 256
#endif
#undef CONFIG_CLOCKS_IN_MHZ
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#ifndef CFG_INIT_RAM_LOCK
-#define CFG_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#ifndef CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */
#else
-#define CFG_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */
#endif
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE 1
-#define CFG_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
-#define CFG_BAUDRATE_TABLE \
+#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
/* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#endif
/*
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-
-#define CFG_64BIT_VSPRINTF 1
-#define CFG_64BIT_STRTOUL 1
-
/*
* I2C
*/
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
-#define CFG_I2C_OFFSET 0x3100
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET 0x3100
/*
* RapidIO MMU
*/
-#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
-#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+#define CONFIG_SYS_RIO_MEM_BASE 0x80000000 /* base address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_RIO_MEM_PHYS 0x0000000c00000000ULL
+#else
+#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE
+#endif
+#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
/*
* General PCI
* Addresses are mapped 1-1.
*/
-#define CFG_PCI1_MEM_BASE 0x80000000
-#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0x00000000
-#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
-
-/* PCI view of System Memory */
-#define CFG_PCI_MEMORY_BUS 0x00000000
-#define CFG_PCI_MEMORY_PHYS 0x00000000
-#define CFG_PCI_MEMORY_SIZE 0x80000000
-
-/* For RTL8139 */
-#define KSEG1ADDR(x) ({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
-#define _IO_BASE 0x00000000
-
-#define CFG_PCI2_MEM_BASE 0xa0000000
-#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe3000000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+
+#define CONFIG_SYS_PCI1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCI1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCI1_MEM_PHYS 0x0000000c00000000ULL
+#else
+#define CONFIG_SYS_PCI1_MEM_BUS CONFIG_SYS_PCI1_MEM_VIRT
+#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_VIRT
+#endif
+#define CONFIG_SYS_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI1_IO_BUS 0x00000000
+#define CONFIG_SYS_PCI1_IO_VIRT 0xffc00000
+#define CONFIG_SYS_PCI1_IO_PHYS (CONFIG_SYS_PCI1_IO_VIRT \
+ | CONFIG_SYS_PHYS_ADDR_HIGH)
+#define CONFIG_SYS_PCI1_IO_SIZE 0x00010000 /* 64K */
+
+#ifdef CONFIG_PHYS_64BIT
+/*
+ * Use the same PCI bus address on PCI1 and PCI2 if we have PHYS_64BIT.
+ * This will increase the amount of PCI address space available for
+ * for mapping RAM.
+ */
+#define CONFIG_SYS_PCI2_MEM_BUS CONFIG_SYS_PCI1_MEM_BUS
+#else
+#define CONFIG_SYS_PCI2_MEM_BUS (CONFIG_SYS_PCI1_MEM_BUS \
+ + CONFIG_SYS_PCI1_MEM_SIZE)
+#endif
+#define CONFIG_SYS_PCI2_MEM_VIRT (CONFIG_SYS_PCI1_MEM_VIRT \
+ + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI2_MEM_PHYS (CONFIG_SYS_PCI1_MEM_PHYS \
+ + CONFIG_SYS_PCI1_MEM_SIZE)
+#define CONFIG_SYS_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CONFIG_SYS_PCI2_IO_BUS 0x00000000
+#define CONFIG_SYS_PCI2_IO_VIRT (CONFIG_SYS_PCI1_IO_VIRT \
+ + CONFIG_SYS_PCI1_IO_SIZE)
+#define CONFIG_SYS_PCI2_IO_PHYS (CONFIG_SYS_PCI1_IO_PHYS \
+ + CONFIG_SYS_PCI1_IO_SIZE)
+#define CONFIG_SYS_PCI2_IO_SIZE CONFIG_SYS_PCI1_IO_SIZE
#if defined(CONFIG_PCI)
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#undef CFG_SCSI_SCAN_BUS_REVERSE
+#undef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_OHCI 1
#define CONFIG_USB_OHCI_NEW 1
#define CONFIG_USB_KEYBOARD 1
-#define CFG_DEVICE_DEREGISTER
-#define CFG_USB_EVENT_POLL 1
-#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
-#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
-#define CFG_OHCI_SWAP_REG_ACCESS 1
-
-#if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
-#endif
+#define CONFIG_SYS_STDIO_DEREGISTER
+#define CONFIG_SYS_USB_EVENT_POLL 1
+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci"
+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
+#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
/*PCIE video card used*/
-#define VIDEO_IO_OFFSET CFG_PCI2_IO_PHYS
+#define VIDEO_IO_OFFSET CONFIG_SYS_PCI2_IO_VIRT
/*PCI video card used*/
-/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/
+/*#define VIDEO_IO_OFFSET CONFIG_SYS_PCI1_IO_VIRT*/
/* video */
#define CONFIG_VIDEO
#define CONFIG_ATI_RADEON_FB
#define CONFIG_VIDEO_LOGO
/*#define CONFIG_CONSOLE_CURSOR*/
-#define CFG_ISA_IO_BASE_ADDRESS CFG_PCI2_IO_PHYS
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCI2_IO_VIRT
#endif
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#ifdef CONFIG_SCSI_AHCI
#define CONFIG_SATA_ULI5288
-#define CFG_SCSI_MAX_SCSI_ID 4
-#define CFG_SCSI_MAX_LUN 1
-#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
-#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
+#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
+#define CONFIG_SYS_SCSI_MAX_LUN 1
+#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
+#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif
#define CONFIG_MPC86XX_PCI2
#endif /* CONFIG_TSEC_ENET */
+/* Contort an addr into the format needed for BATs */
+#ifdef CONFIG_PHYS_64BIT
+#define BAT_PHYS_ADDR(x) ((unsigned long) \
+ ((x & 0x00000000ffffffffULL) | \
+ ((x & 0x0000000e00000000ULL) >> 24) | \
+ ((x & 0x0000000100000000ULL) >> 30)))
+#else
+#define BAT_PHYS_ADDR(x) (x)
+#endif
+
+
+/* Put high physical address bits into the BAT format */
+#define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8)
+#define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2)
+
/*
- * BAT0 2G Cacheable, non-guarded
- * 0x0000_0000 2G DDR
+ * BAT0 DDR
*/
-#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
-#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
-#define CFG_IBAT0U CFG_DBAT0U
+#define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
/*
- * BAT1 1G Cache-inhibited, guarded
- * 0x8000_0000 512M PCI-Express 1 Memory
- * 0xa000_0000 512M PCI-Express 2 Memory
- * Changed it for operating from 0xd0000000
+ * BAT1 LBC (PIXIS/CF)
+ */
+#define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \
+ | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS) \
+ | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U
+
+/* if CONFIG_PCI:
+ * BAT2 PCI1 and PCI1 MEM
+ * if CONFIG_RIO
+ * BAT2 Rapidio Memory
*/
-#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
+#ifdef CONFIG_PCI
+#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G \
+ | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_MEM_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
+#else /* CONFIG_RIO */
+#define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT | \
+ BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M \
+ | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_RIO_MEM_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT1U CFG_DBAT1U
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
+#endif
/*
- * BAT2 512M Cache-inhibited, guarded
- * 0xc000_0000 512M RapidIO Memory
+ * BAT3 CCSR Space
+ * This BAT is used early; don't use any macros with ULL - use HIGH/LOW pairs
+ * instead. The assembler chokes on ULL.
*/
-#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \
- | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U CFG_DBAT2U
+#define CONFIG_SYS_DBAT3L (CONFIG_SYS_CCSRBAR_PHYS_LOW \
+ | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+ | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT3L (CONFIG_SYS_CCSRBAR_PHYS_LOW \
+ | PHYS_HIGH_TO_BXPN(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+ | PHYS_HIGH_TO_BX(CONFIG_SYS_CCSRBAR_PHYS_HIGH) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U
+
+#if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
+#endif
/*
- * BAT3 4M Cache-inhibited, guarded
- * 0xf800_0000 4M CCSR
+ * BAT4 PCI1_IO and PCI2_IO
*/
-#define CFG_DBAT3L ( CFG_CCSRBAR | BATL_PP_RW \
- | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT3U (CFG_CCSRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CFG_IBAT3L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U CFG_DBAT3U
+#define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_128K \
+ | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCI1_IO_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U
/*
- * BAT4 32M Cache-inhibited, guarded
- * 0xe200_0000 16M PCI-Express 1 I/O
- * 0xe300_0000 16M PCI-Express 2 I/0
- * Note that this is at 0xe0000000
+ * BAT5 Init RAM for stack in the CPU DCache (no backing memory)
*/
-#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
- | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
-#define CFG_IBAT4U CFG_DBAT4U
+#define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L
+#define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U
/*
- * BAT5 128K Cacheable, non-guarded
- * 0xe401_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
+ * BAT6 FLASH
*/
-#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_IBAT5L CFG_DBAT5L
-#define CFG_IBAT5U CFG_DBAT5U
+#define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+ | BATL_PP_RW | BATL_CACHEINHIBIT \
+ | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \
+ | BATU_VP)
+#define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
+ | BATL_PP_RW | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U
+
+/* Map the last 1M of flash where we're running from reset */
+#define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+ | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U_EARLY (TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
+ | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
/*
- * BAT6 32M Cache-inhibited, guarded
- * 0xfe00_0000 32M FLASH
+ * BAT7 FREE - used later for tmp mappings
*/
-#define CFG_DBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW \
- | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT6U ((CFG_FLASH_BASE & 0xfe000000) | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT6L ((CFG_FLASH_BASE & 0xfe000000) | BATL_PP_RW | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U CFG_DBAT6U
-
-#define CFG_DBAT7L 0x00000000
-#define CFG_DBAT7U 0x00000000
-#define CFG_IBAT7L 0x00000000
-#define CFG_IBAT7U 0x00000000
+#define CONFIG_SYS_DBAT7L 0x00000000
+#define CONFIG_SYS_DBAT7U 0x00000000
+#define CONFIG_SYS_IBAT7L 0x00000000
+#define CONFIG_SYS_IBAT7U 0x00000000
/*
* Environment
*/
-#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000)
- #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
- #define CFG_ENV_SIZE 0x2000
+#ifndef CONFIG_SYS_RAMBOOT
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x60000)
+ #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#else
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#endif
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
#define CONFIG_CMD_I2C
#define CONFIG_CMD_REGINFO
-#if defined(CFG_RAMBOOT)
- #undef CONFIG_CMD_ENV
+#if defined(CONFIG_SYS_RAMBOOT)
+ #undef CONFIG_CMD_SAVEENV
#endif
#if defined(CONFIG_PCI)
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CFG_LOAD_ADDR 0x2000000 /* default load address */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
- #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
- #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
"ramdiskfile=your.ramdisk.u-boot\0" \
"fdtaddr=c00000\0" \
"fdtfile=mpc8641_hpcn.dtb\0" \
- "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
- "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
+ "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \
+ "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \
"maxcpus=2"