#define CFG_RESET_ADDRESS 0xfff00100
-/*#undef CONFIG_PCI*/
-#define CONFIG_PCI
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI1 1 /* PCIE controler 1 (ULI bridge) */
+#define CONFIG_PCI2 1 /* PCIE controler 2 (slot) */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define L2_ENABLE (L2CR_L2E)
#ifndef CONFIG_SYS_CLK_FREQ
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
#endif
#define CFG_CCSRBAR 0xf8000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCI2_ADDR (CFG_CCSRBAR+0x9000)
+
/*
* DDR Setup
*/
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
-#define CFG_PCI1_IO_BASE 0xe2000000
-#define CFG_PCI1_IO_PHYS CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
/* PCI view of System Memory */
#define CFG_PCI_MEMORY_BUS 0x00000000
#define CFG_PCI2_MEM_BASE 0xa0000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PCI2_IO_BASE 0xe3000000
-#define CFG_PCI2_IO_PHYS CFG_PCI2_IO_BASE
-#define CFG_PCI2_IO_SIZE 0x1000000 /* 16M */
+#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_IO_BASE 0x00000000
+#define CFG_PCI2_IO_PHYS 0xe3000000
+#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
#if defined(CONFIG_PCI)
#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CFG_PCI2_IO_PHYS
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS CFG_PCI2_IO_PHYS
+#endif
+
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_DOS_PARTITION
#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
#endif
+#define CONFIG_MPC86XX_PCI2
+
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC86XX_TSEC1 1
-#define CONFIG_MPC86XX_TSEC1_NAME "eTSEC1"
-#define CONFIG_MPC86XX_TSEC2 1
-#define CONFIG_MPC86XX_TSEC2_NAME "eTSEC2"
-#define CONFIG_MPC86XX_TSEC3 1
-#define CONFIG_MPC86XX_TSEC3_NAME "eTSEC3"
-#define CONFIG_MPC86XX_TSEC4 1
-#define CONFIG_MPC86XX_TSEC4_NAME "eTSEC4"
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define CONFIG_TSEC3 1
+#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_TSEC4 1
+#define CONFIG_TSEC4_NAME "eTSEC4"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
* 0xa000_0000 512M PCI-Express 2 Memory
* Changed it for operating from 0xd0000000
*/
-#define CFG_DBAT1L ( CFG_PCI1_MEM_BASE | BATL_PP_RW \
+#define CFG_DBAT1L ( CFG_PCI1_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT1U (CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT1L (CFG_PCI1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
+#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT1U CFG_DBAT1U
/*
* BAT2 512M Cache-inhibited, guarded
* 0xc000_0000 512M RapidIO Memory
*/
-#define CFG_DBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW \
+#define CFG_DBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U (CFG_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L (CFG_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT2U (CFG_RIO_MEM_PHYS | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CFG_IBAT2L (CFG_RIO_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT2U CFG_DBAT2U
/*
* 0xe300_0000 16M PCI-Express 2 I/0
* Note that this is at 0xe0000000
*/
-#define CFG_DBAT4L ( CFG_PCI1_IO_BASE | BATL_PP_RW \
+#define CFG_DBAT4L ( CFG_PCI1_IO_PHYS | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT4U (CFG_PCI1_IO_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L (CFG_PCI1_IO_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CFG_DBAT4U (CFG_PCI1_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CFG_IBAT4L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CFG_IBAT4U CFG_DBAT4U
/*
*/
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x60000)
+ #define CFG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+
#if defined(CFG_RAMBOOT)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C \
- | CFG_CMD_SCSI \
- | CFG_CMD_USB \
- | CFG_CMD_EXT2) \
- & \
- ~(CFG_CMD_ENV))
- #else
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_SCSI \
- | CFG_CMD_USB \
- | CFG_CMD_EXT2)
- #else
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C)
- #endif
+ #undef CONFIG_CMD_ENV
+#endif
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+ #define CONFIG_CMD_SCSI
+ #define CONFIG_CMD_EXT2
#endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
/* Cache Configuration */
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
#endif
/*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#if defined(CONFIG_CMD_KGDB)
+ #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+ #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/*
#define CONFIG_HOSTNAME unknown
#define CONFIG_ROOTPATH /opt/nfsroot
#define CONFIG_BOOTFILE uImage
+#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_SERVERIP 192.168.1.1
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=your.ramdisk.u-boot\0" \
- "dtbaddr=400000\0" \
+ "dtbaddr=c00000\0" \
"dtbfile=mpc8641_hpcn.dtb\0" \
"en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
"dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
projects / kernel / u-boot.git / blobdiff