disk: convert CONFIG_DOS_PARTITION to Kconfig

[platform/kernel/u-boot.git] / include / configs / MPC8641HPCN.h

diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index f90f7f2..0e5bbc0 100644 (file)
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -16,14 +16,9 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_DISPLAY_BOARDINFO
-
 /* High Level Configuration Options */
-#define CONFIG_MPC8641         1       /* MPC8641 specific */
-#define CONFIG_MPC8641HPCN     1       /* MPC8641HPCN board specific */
 #define CONFIG_MP              1       /* support multiple processors */
 #define CONFIG_LINUX_RESET_VEC 0x100   /* Reset vector used by Linux */
-/*#define CONFIG_PHYS_64BIT    1*/     /* Place devices in 36-bit space */
 #define CONFIG_ADDR_MAP                1       /* Use addr map */
 
 /*
@@ -45,12 +40,10 @@
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1                   /* SRIO port 1 */
 
-#define CONFIG_PCI             1       /* Enable PCI/PCIE */
 #define CONFIG_PCIE1           1       /* PCIE controller 1 (ULI bridge) */
 #define CONFIG_PCIE2           1       /* PCIE controller 2 (slot) */
 #define CONFIG_FSL_PCI_INIT    1       /* Use common FSL init code */
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
-#define CONFIG_FSL_LAW         1       /* Use common FSL law init code */
 
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_ENV_OVERWRITE
@@ -93,7 +86,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
 #define CONFIG_SYS_CCSRBAR             0xffe00000      /* relocated CCSRBAR */
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
@@ -109,7 +101,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * DDR Setup
  */
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -122,7 +113,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_MAX_DDR_BAT_SIZE    0x80000000      /* BAT mapping size */
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_NUM_DDR_CONTROLLERS     2
 #define CONFIG_DIMM_SLOTS_PER_CTLR     2
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
@@ -354,8 +344,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
 
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
@@ -364,8 +352,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  ************************************************************/
 #define CONFIG_PCI_OHCI                        1
 #define CONFIG_USB_OHCI_NEW            1
-#define CONFIG_USB_KEYBOARD            1
-#define CONFIG_SYS_STDIO_DEREGISTER
 #define CONFIG_SYS_USB_EVENT_POLL              1
 #define CONFIG_SYS_USB_OHCI_SLOT_NAME          "ohci_pci"
 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS     15
@@ -378,13 +364,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*#define VIDEO_IO_OFFSET      CONFIG_SYS_PCIE1_IO_VIRT*/
 
 /* video */
-#define CONFIG_VIDEO
 
 #if defined(CONFIG_VIDEO)
 #define CONFIG_BIOSEMU
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_VGA_AS_SINGLE_DEVICE
 #define CONFIG_ATI_RADEON_FB
 #define CONFIG_VIDEO_LOGO
 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT
@@ -392,7 +374,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #undef CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 
-#define CONFIG_DOS_PARTITION
 #define CONFIG_SCSI_AHCI
 
 #ifdef CONFIG_SCSI_AHCI
@@ -637,7 +618,8 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ   (256 << 20)     /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (256 << 20)     /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
     #define CONFIG_KGDB_BAUDRATE       230400  /* speed to run kgdb serial port */
@@ -664,7 +646,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_NETMASK         255.255.255.0
 
 /* default location for tftp and bootm */
-#define CONFIG_LOADADDR                1000000
+#define CONFIG_LOADADDR                0x10000000
 
 #undef CONFIG_BOOTARGS         /* the boot command will set bootargs */
 
@@ -685,9 +667,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
                "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
                        " $filesize\0"  \
        "consoledev=ttyS0\0"                                            \
-       "ramdiskaddr=2000000\0"                                         \
+       "ramdiskaddr=0x18000000\0"                                              \
        "ramdiskfile=your.ramdisk.u-boot\0"                             \
-       "fdtaddr=c00000\0"                                              \
+       "fdtaddr=0x17c00000\0"                                          \
        "fdtfile=mpc8641_hpcn.dtb\0"                                    \
        "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0"                        \
        "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \