Merge remote-tracking branch 'u-boot-imx/master'

[platform/kernel/u-boot.git] / include / configs / MPC8572DS.h

diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index d93185c..d1b5b70 100644 (file)
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -112,22 +112,11 @@
 #define CONFIG_SYS_L2_SIZE             (512 << 10)
 #define CONFIG_SYS_INIT_L2_END (CONFIG_SYS_INIT_L2_ADDR + CONFIG_SYS_L2_SIZE)
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR             0xffe00000      /* relocated CCSRBAR */
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_CCSRBAR_PHYS                0xfffe00000ull  /* physical addr of CCSRBAR */
-#else
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#endif
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xffe00000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
-#if defined(CONFIG_RAMBOOT_NAND) && !defined(CONFIG_NAND_SPL)
-#define CONFIG_SYS_CCSRBAR_DEFAULT             CONFIG_SYS_CCSRBAR
-#else
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
+#if defined(CONFIG_NAND_SPL)
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
 #endif
 
 /* DDR Setup */
@@ -216,8 +205,7 @@
 
 
 #define CONFIG_FLASH_BR_PRELIM \
-       (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) \
-       | BR_PS_16 | BR_V)
+       (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000) | BR_PS_16 | BR_V)
 #define CONFIG_FLASH_OR_PRELIM 0xf8000ff7
 
 #define CONFIG_SYS_BR1_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
@@ -387,20 +375,20 @@
 #define CONFIG_SYS_BR2_PRELIM  CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Address */
 #define CONFIG_SYS_OR2_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 #endif
-#define CONFIG_SYS_BR4_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x40000))\
+#define CONFIG_SYS_BR4_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x40000) \
                               | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                               | BR_PS_8               /* Port Size = 8 bit */ \
                               | BR_MS_FCM             /* MSEL = FCM */ \
                               | BR_V)                 /* valid */
 #define CONFIG_SYS_OR4_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
-#define CONFIG_SYS_BR5_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0x80000))\
+#define CONFIG_SYS_BR5_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0x80000)\
                               | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                               | BR_PS_8               /* Port Size = 8 bit */ \
                               | BR_MS_FCM             /* MSEL = FCM */ \
                               | BR_V)                 /* valid */
 #define CONFIG_SYS_OR5_PRELIM  CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */
 
-#define CONFIG_SYS_BR6_PRELIM  (BR_PHYS_ADDR((CONFIG_SYS_NAND_BASE_PHYS + 0xc0000))\
+#define CONFIG_SYS_BR6_PRELIM  (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS + 0xc0000)\
                               | (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
                               | BR_PS_8               /* Port Size = 8 bit */ \
                               | BR_MS_FCM             /* MSEL = FCM */ \
@@ -429,9 +417,6 @@
 
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
 
 /*
  * Pass open firmware flat tree
@@ -551,7 +536,6 @@
 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
 #endif
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -582,10 +566,6 @@
 
 #if defined(CONFIG_TSEC_ENET)
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #define CONFIG_MII             1       /* MII PHY management */
 #define CONFIG_MII_DEFAULT_TSEC        1       /* Allow unregistered phys */
 #define CONFIG_TSEC1   1
@@ -708,11 +688,11 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (16 << 20)      /* Increase max gunzip size */
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
@@ -738,8 +718,8 @@
 #define CONFIG_IPADDR          192.168.1.254
 
 #define CONFIG_HOSTNAME                unknown
-#define CONFIG_ROOTPATH                /opt/nfsroot
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/opt/nfsroot"
+#define CONFIG_BOOTFILE                "uImage"
 #define CONFIG_UBOOTPATH       u-boot.bin      /* U-Boot image on TFTP server */
 
 #define CONFIG_SERVERIP                192.168.1.1