#ifndef __CONFIG_H
#define __CONFIG_H
+#ifdef CONFIG_MK_36BIT
+#define CONFIG_PHYS_64BIT
+#endif
+
/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC8572 1
#define CONFIG_MPC8572DS 1
#define CONFIG_MP 1 /* support multiple processors */
-#define CONFIG_NUM_CPUS 2 /* Number of CPUs in the system */
#define CONFIG_FSL_ELBC 1 /* Has Enhanced localbus controller */
#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash associated with the CDS board.
- * This allows booting from a promjet.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy);
extern unsigned long get_board_ddr_clk(unsigned long dummy);
#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR+0xa000)
/* DDR Setup */
-#define CONFIG_SYS_DDR_TLB_START 9
#define CONFIG_VERY_BIG_RAM
#define CONFIG_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
#define PIXIS_VCORE0 0x14 /* VELA VCORE0 Register */
#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
+#define PIXIS_VBOOT_LBMAP 0xc0 /* VBOOT - CFG_LBMAP */
+#define PIXIS_VBOOT_LBMAP_NOR0 0x00 /* cfg_lbmap - boot from NOR 0 */
+#define PIXIS_VBOOT_LBMAP_PJET 0x01 /* cfg_lbmap - boot from projet */
+#define PIXIS_VBOOT_LBMAP_NAND 0x02 /* cfg_lbmap - boot from NAND */
+#define PIXIS_VBOOT_LBMAP_NOR1 0x03 /* cfg_lbmap - boot from NOR 1 */
#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VSPEED2 0x19 /* VELA VSpeed 2 */
#define CONFIG_OF_BOARD_SETUP 1
#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define CONFIG_SYS_64BIT_VSPRINTF 1
-#define CONFIG_SYS_64BIT_STRTOUL 1
-
/* new uImage format support */
#define CONFIG_FIT 1
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
#undef CONFIG_TULIP
#undef CONFIG_RTL8139
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x) (x)
-#define _IO_BASE 0x00000000
-#endif
-
#ifndef CONFIG_PCI_PNP
#define PCI_ENET0_IOADDR CONFIG_SYS_PCIE3_IO_BUS
#define PCI_ENET0_MEMADDR CONFIG_SYS_PCIE3_IO_BUS
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BEDBUG
#define CONFIG_CMD_NET
#define CONFIG_CMD_SCSI
#define CONFIG_CMD_EXT2
/*
* For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions