+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2007-2008,2010-2011 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#include "../board/freescale/common/ics307_clk.h"
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE 0xeff40000
-#endif
-
#ifndef CONFIG_RESET_VECTOR_ADDRESS
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
#endif
#endif
/* High Level Configuration Options */
-#define CONFIG_MP 1 /* support multiple processors */
#define CONFIG_PCIE1 1 /* PCIE controller 1 (slot 1) */
#define CONFIG_PCIE2 1 /* PCIE controller 2 (slot 2) */
#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */
#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x7fffffff
-#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
* Config the L2 Cache as L2 SRAM
/* DDR Setup */
#define CONFIG_VERY_BIG_RAM
-#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#define CONFIG_DDR_SPD
#undef CONFIG_SYS_RAMBOOT
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */
-
#define CONFIG_HWCONFIG /* enable hwconfig */
#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
#define PIXIS_BASE 0xffdf0000 /* PIXIS registers */
CONFIG_SYS_NAND_BASE + 0x80000,\
CONFIG_SYS_NAND_BASE + 0xC0000}
#define CONFIG_SYS_MAX_NAND_DEVICE 4
-#define CONFIG_CMD_NAND 1
#define CONFIG_NAND_FSL_ELBC 1
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_MAX_OOBFREE 5
* open - index 2
* shorted - index 1
*/
-#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
#endif
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CONFIG_SCSI_AHCI
#ifdef CONFIG_SCSI_AHCI
-#define CONFIG_LIBATA
#define CONFIG_SATA_ULI5288
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 4
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
-#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#endif /* SCSI */
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define TSEC4_PHYIDX 0
#define CONFIG_ETHPRIME "eTSEC1"
-
-#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
#endif /* CONFIG_TSEC_ENET */
/*
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
- * Command line configuration.
- */
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#endif
-
-/*
* USB
*/
#ifdef CONFIG_USB_EHCI_HCD
-#define CONFIG_USB_EHCI_PCI
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_PCI_EHCI_DEVICE 0
#endif
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
/*
* For booting Linux, the board info and command line data
#define CONFIG_IPADDR 192.168.1.254
-#define CONFIG_HOSTNAME unknown
+#define CONFIG_HOSTNAME "unknown"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 1000000
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1,ecc=off\0" \
"netdev=eth0\0" \