Convert CONFIG_CMD_REGINFO to Kconfig

[platform/kernel/u-boot.git] / include / configs / MPC8572DS.h

diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index 5ca01e8..0960ff5 100644 (file)
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -28,7 +28,6 @@
 /* High Level Configuration Options */
 #define CONFIG_MP              1       /* support multiple processors */
 
-#define CONFIG_FSL_ELBC                1       /* Has Enhanced localbus controller */
 #define CONFIG_PCIE1           1       /* PCIE controller 1 (slot 1) */
 #define CONFIG_PCIE2           1       /* PCIE controller 2 (slot 2) */
 #define CONFIG_PCIE3           1       /* PCIE controller 3 (ULI bridge) */
@@ -286,7 +285,6 @@
                                CONFIG_SYS_NAND_BASE + 0x80000,\
                                CONFIG_SYS_NAND_BASE + 0xC0000}
 #define CONFIG_SYS_MAX_NAND_DEVICE    4
-#define CONFIG_CMD_NAND                1
 #define CONFIG_NAND_FSL_ELBC   1
 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
 #define CONFIG_SYS_NAND_MAX_OOBFREE    5
@@ -471,7 +469,6 @@
 #endif
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #define CONFIG_SCSI_AHCI
 
 #ifdef CONFIG_SCSI_AHCI
@@ -522,8 +519,6 @@
 #define TSEC4_PHYIDX           0
 
 #define CONFIG_ETHPRIME                "eTSEC1"
-
-#define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
 #endif /* CONFIG_TSEC_ENET */
 
 /*
@@ -533,7 +528,6 @@
 #if defined(CONFIG_SYS_RAMBOOT)
 
 #else
-       #define CONFIG_ENV_IS_IN_FLASH  1
        #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
        #define CONFIG_ENV_ADDR 0xfff80000
        #else
@@ -547,27 +541,13 @@
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-#define CONFIG_CMD_PCI
-#define CONFIG_SCSI
-#endif
-
-/*
  * USB
  */
-#define CONFIG_USB_EHCI
 
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_PCI
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_PCI_EHCI_DEVICE                 0
-#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS     2
 #endif
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
@@ -626,8 +606,6 @@
 
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
 "hwconfig=fsl_ddr:ctlr_intlv=bank,bank_intlv=cs0_cs1,ecc=off\0"                \
 "netdev=eth0\0"                                                \