powerpc: Cleanup BOOTFLAG_* references

[platform/kernel/u-boot.git] / include / configs / MPC8568MDS.h

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 0cc2d47..d6171b4 100644 (file)
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -33,6 +33,8 @@
 #define CONFIG_MPC8568         1       /* MPC8568 specific */
 #define CONFIG_MPC8568MDS      1       /* MPC8568MDS board specific */
 
+#define        CONFIG_SYS_TEXT_BASE    0xfff80000
+
 #define CONFIG_PCI             1       /* Enable PCI/PCIE */
 #define CONFIG_PCI1            1       /* PCI controller */
 #define CONFIG_PCIE1           1       /* PCIE controller */
@@ -75,9 +77,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
 #define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
 
-#define CONFIG_SYS_PCI1_ADDR           (CONFIG_SYS_CCSRBAR+0x8000)
-#define CONFIG_SYS_PCIE1_ADDR          (CONFIG_SYS_CCSRBAR+0xa000)
-
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -157,7 +156,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500             /* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
@@ -247,7 +246,6 @@ extern unsigned long get_clock_freq(void);
 
 /* Serial Port */
 #define CONFIG_CONS_INDEX              1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -316,7 +314,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_UEC_ETH
 #ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME         "FSL UEC0"
+#define CONFIG_ETHPRIME         "UEC0"
 #endif
 #define CONFIG_PHY_MODE_NEED_CHANGE
 #define CONFIG_eTSEC_MDIO_BUS
@@ -434,7 +432,8 @@ extern unsigned long get_clock_freq(void);
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x2000000       /* default load address */
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 #if defined(CONFIG_CMD_KGDB)
@@ -454,14 +453,6 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02            /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */