#ifndef __CONFIG_H
#define __CONFIG_H
-#define CONFIG_DISPLAY_BOARDINFO
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC8568 1 /* MPC8568 specific */
-#define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */
-
#define CONFIG_SYS_TEXT_BASE 0xfff80000
#define CONFIG_SYS_SRIO
#define CONFIG_SRIO1 /* SRIO port 1 */
-#define CONFIG_PCI 1 /* Enable PCI/PCIE */
#define CONFIG_PCI1 1 /* PCI controller */
#define CONFIG_PCIE1 1 /* PCIE controller */
#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_QE /* Enable QE */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x00400000
#define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR
/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
#undef CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_SPD
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#endif /* CONFIG_QE */
#if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
-
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
/*
* Environment
*/
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
-#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
/*
* Command line configuration.
*/
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_REGINFO
#if defined(CONFIG_PCI)
#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \