Merge branch 'master' of git://git.denx.de/u-boot-video

[platform/kernel/u-boot.git] / include / configs / MPC8568MDS.h

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index f684e79..994e7ae 100644 (file)
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -71,14 +71,8 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest works on */
 #define CONFIG_SYS_MEMTEST_END         0x00400000
 
-/*
- * Base addresses -- Note these are effective addresses where the
- * actual resources get mapped (not physical addresses)
- */
-#define CONFIG_SYS_CCSRBAR_DEFAULT     0xff700000      /* CCSRBAR Default */
-#define CONFIG_SYS_CCSRBAR             0xe0000000      /* relocated CCSRBAR */
-#define CONFIG_SYS_CCSRBAR_PHYS        CONFIG_SYS_CCSRBAR      /* physical addr of CCSRBAR */
-#define CONFIG_SYS_IMMR                CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_CCSRBAR             0xe0000000
+#define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_FSL_DDR2
@@ -334,7 +328,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC1_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC1_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR       7
-#define CONFIG_SYS_UEC1_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 #endif
 
@@ -346,14 +340,13 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_UEC2_TX_CLK         QE_CLK16
 #define CONFIG_SYS_UEC2_ETH_TYPE       GIGA_ETH
 #define CONFIG_SYS_UEC2_PHY_ADDR       1
-#define CONFIG_SYS_UEC2_INTERFACE_TYPE RGMII_ID
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_ID
 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 #endif
 #endif /* CONFIG_QE */
 
 #if defined(CONFIG_PCI)
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP                 /* do pci plug-and-play */
 
 #undef CONFIG_EEPRO100
@@ -364,10 +357,6 @@ extern unsigned long get_clock_freq(void);
 
 #endif /* CONFIG_PCI */
 
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_MII             1       /* MII PHY management */
@@ -451,10 +440,11 @@ extern unsigned long get_clock_freq(void);
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
+ * have to be in the first 64 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */