/* High Level Configuration Options */
#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48/68 */
#define CONFIG_MPC8568 1 /* MPC8568 specific */
#define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */
-#undef CONFIG_PCI
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI1 1 /* PCI controller */
+#define CONFIG_PCIE1 1 /* PCIE controller */
+#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_QE /* Enable QE */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
/*#define CONFIG_DDR_2T_TIMING Sets the 2T timing bit */
/*#define CONFIG_DDR_ECC*/ /* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */
+/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-/*#define CONFIG_L2_CACHE*/ /* toggle L2 cache */
-#define CONFIG_BTB /* toggle branch predition */
-#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
/*
* Only possible on E500 Version 2 or newer cores.
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+
/*
* DDR Setup
*/
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8568@0"
-#define OF_SOC "soc8568@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8568@e0000000/serial@4600"
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* I2C
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_EEPROM_ADDR 0x57
+#define CFG_I2C_EEPROM_ADDR 0x52
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {{0,0x69}} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
+#define CFG_I2C2_OFFSET 0x3100
/*
* General PCI
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
-#define CFG_PEX_MEM_BASE 0xa0000000
-#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
-#define CFG_PEX_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PEX_IO_BASE 0x00000000
-#define CFG_PEX_IO_PHYS 0xe2800000
-#define CFG_PEX_IO_SIZE 0x00800000 /* 8M */
+#define CFG_PCIE1_MEM_BASE 0xa0000000
+#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCIE1_IO_BASE 0x00000000
+#define CFG_PCIE1_IO_PHYS 0xe2800000
+#define CFG_PCIE1_IO_SIZE 0x00800000 /* 8M */
#define CFG_SRIO_MEM_BASE 0xc0000000
+#ifdef CONFIG_QE
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#ifndef CONFIG_TSEC_ENET
+#define CONFIG_ETHPRIME "FSL UEC0"
+#endif
+#define CONFIG_PHY_MODE_NEED_CHANGE
+#define CONFIG_eTSEC_MDIO_BUS
+
+#ifdef CONFIG_eTSEC_MDIO_BUS
+#define CONFIG_MIIM_ADDRESS 0xE0024520
+#endif
+
+#define CONFIG_UEC_ETH1 /* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM 0 /* UCC1 */
+#define CFG_UEC1_RX_CLK QE_CLK_NONE
+#define CFG_UEC1_TX_CLK QE_CLK16
+#define CFG_UEC1_ETH_TYPE GIGA_ETH
+#define CFG_UEC1_PHY_ADDR 7
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2 /* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
+#define CFG_UEC2_RX_CLK QE_CLK_NONE
+#define CFG_UEC2_TX_CLK QE_CLK16
+#define CFG_UEC2_ETH_TYPE GIGA_ETH
+#define CFG_UEC2_PHY_ADDR 1
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+#endif /* CONFIG_QE */
+
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#endif /* CONFIG_PCI */
-
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
-#if defined(CONFIG_TSEC_ENET)
+#endif /* CONFIG_PCI */
#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
#endif
+#if defined(CONFIG_TSEC_ENET)
+
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "eTSEC1"
-#undef CONFIG_TSEC3
-#undef CONFIG_TSEC4
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 2
#define TSEC2_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-/* Options are: eTSEC[0-3] */
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
#define CONFIG_ETHPRIME "eTSEC0"
#endif /* CONFIG_TSEC_ENET */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
*/
/* The mac addresses for all ethernet interface */
-#if defined(CONFIG_TSEC_ENET)
+#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_UEC_ETH)
+#define CONFIG_HAS_ETH0
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
#define CONFIG_HAS_ETH2
#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.253