Makefile: move all Power Architecture boards into boards.cfg

[platform/kernel/u-boot.git] / include / configs / MPC8560ADS.h

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index 761a370..fad180f 100644 (file)
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -42,12 +42,19 @@
 #define CONFIG_MPC8560ADS      1       /* MPC8560ADS board specific */
 #define CONFIG_MPC8560         1
 
+/*
+ * default CCARBAR is at 0xff700000
+ * assume U-Boot is less than 0.5MB
+ */
+#define        CONFIG_SYS_TEXT_BASE    0xfff80000
+
 #define CONFIG_PCI
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
+#define CONFIG_RESET_PHY_R     1       /* Call reset_phy() */
 
 /*
  * sysclk for MPC85xx
@@ -133,7 +140,7 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
@@ -252,9 +259,6 @@
 #define CONFIG_OF_BOARD_SETUP          1
 #define CONFIG_OF_STDOUT_VIA_ALIAS     1
 
-#define CONFIG_SYS_64BIT_VSPRINTF      1
-#define CONFIG_SYS_64BIT_STRTOUL       1
-
 /*
  * I2C
  */
@@ -362,6 +366,10 @@
  * GPIO pins used for bit-banged MII communications
  */
 #define MDIO_PORT      2               /* Port C */
+#define MDIO_DECLARE   volatile ioport_t *iop = ioport_addr ( \
+                               (immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
+#define MDC_DECLARE    MDIO_DECLARE
+
 #define MDIO_ACTIVE    (iop->pdir |=  0x00400000)
 #define MDIO_TRISTATE  (iop->pdir &= ~0x00400000)
 #define MDIO_READ      ((iop->pdat &  0x00400000) != 0)
@@ -414,6 +422,7 @@
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
 
 #if defined(CONFIG_PCI)
     #define CONFIG_CMD_PCI
@@ -435,7 +444,8 @@
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING         /* Command-line editing */
+#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x1000000       /* default load address */
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt */
 
@@ -452,10 +462,10 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 16 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ   (16 << 20)      /* Initial Memory map for Linux*/
 
 /*
  * Internal Definitions