flash: complete CONFIG_SYS_NO_FLASH move with renaming
[platform/kernel/u-boot.git] / include / configs / MPC8560ADS.h
index 8d6e442..f27bdee 100644 (file)
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_DISPLAY_BOARDINFO
-
 /* High Level Configuration Options */
-#define CONFIG_BOOKE           1       /* BOOKE */
-#define CONFIG_E500            1       /* BOOKE e500 family */
 #define CONFIG_CPM2            1       /* has CPM2 */
-#define CONFIG_MPC8560ADS      1       /* MPC8560ADS board specific */
-#define CONFIG_MPC8560         1
 
 /*
  * default CCARBAR is at 0xff700000
  */
 #define        CONFIG_SYS_TEXT_BASE    0xfff80000
 
-#define CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_FSL_LAW         1       /* Use common FSL init code */
 #define CONFIG_RESET_PHY_R     1       /* Call reset_phy() */
 
 /*
@@ -60,7 +52,6 @@
 #define CONFIG_SYS_CLK_FREQ    33000000
 #endif
 
-
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
@@ -76,7 +67,6 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
@@ -86,7 +76,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000      /* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
 #define CONFIG_SYS_LBC_LSDMR_4 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_MRW)
 #define CONFIG_SYS_LBC_LSDMR_5 (CONFIG_SYS_LBC_LSDMR_COMMON | LSDMR_OP_NORMAL)
 
-
 /*
  * 32KB, 8-bit wide for ADS config reg
  */
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#ifdef  CONFIG_SYS_HUSH_PARSER
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_BOARD_SETUP          1
-#define CONFIG_OF_STDOUT_VIA_ALIAS     1
-
 /*
  * I2C
  */
 #define CONFIG_SYS_PCI1_IO_SIZE        0x100000        /* 1M */
 
 #if defined(CONFIG_PCI)
-
-#define CONFIG_PCI_PNP                 /* do pci plug-and-play */
-
 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP
 
 
 #endif /* CONFIG_PCI */
 
-
 #ifdef CONFIG_TSEC_ENET
 
 #ifndef CONFIG_MII
 
 #endif
 
-
 /*
  * Environment
  */
   #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
   #define CONFIG_ENV_SIZE              0x2000
 #else
-  #define CONFIG_SYS_NO_FLASH          1       /* Flash is not usable now */
   #define CONFIG_ENV_IS_NOWHERE        1       /* Store ENV in memory only */
   #define CONFIG_ENV_ADDR              (CONFIG_SYS_MONITOR_BASE - 0x1000)
   #define CONFIG_ENV_SIZE              0x2000
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_I2C
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_REGINFO
 
 #endif
 
 #if defined(CONFIG_ETHER_ON_FCC)
-    #define CONFIG_CMD_MII
 #endif
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed to run kgdb serial port */
 #endif
 
-
 /*
  * Environment Configuration
  */
 
 #define CONFIG_LOADADDR  200000        /* default location for tftp and bootm */
 
-#define CONFIG_BOOTDELAY 10    /* -1 disables auto-boot */
 #undef  CONFIG_BOOTARGS                /* the boot command will set bootargs */
 
 #define CONFIG_BAUDRATE        115200