configs: migrate CONFIG_VIDEO_BMP_RLE8 to defconfigs

[platform/kernel/u-boot.git] / include / configs / MPC8560ADS.h

diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index fe116e0..5e1bef8 100644 (file)
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -1,9 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2004, 2011 Freescale Semiconductor.
  * (C) Copyright 2002,2003 Motorola,Inc.
  * Xianghua Xiao <X.Xiao@motorola.com>
- *
- * SPDX-License-Identifier:    GPL-2.0+
  */
 
 /*
@@ -18,6 +17,8 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
+#include <linux/delay.h>
+
 /* High Level Configuration Options */
 #define CONFIG_CPM2            1       /* has CPM2 */
 
@@ -25,13 +26,10 @@
  * default CCARBAR is at 0xff700000
  * assume U-Boot is less than 0.5MB
  */
-#define        CONFIG_SYS_TEXT_BASE    0xfff80000
 
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #define CONFIG_SYS_PCI_64BIT   1       /* enable 64-bit PCI resources */
-#define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #undef CONFIG_ETHER_ON_FCC             /* cpm FCC ethernet support */
-#define CONFIG_ENV_OVERWRITE
 #define CONFIG_RESET_PHY_R     1       /* Call reset_phy() */
 
 /*
@@ -60,16 +58,12 @@
 
 #define CONFIG_SYS_INIT_DBCR DBCR_IDM          /* Enable Debug Exceptions */
 
-#define CONFIG_SYS_MEMTEST_START       0x00200000      /* memtest region */
-#define CONFIG_SYS_MEMTEST_END         0x00400000
-
 #define CONFIG_SYS_CCSRBAR             0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
-#undef CONFIG_FSL_DDR_INTERACTIVE
 
 #define CONFIG_MEM_INIT_VALUE          0xDeadBeef
 
@@ -116,12 +110,8 @@
 #undef  CONFIG_SYS_RAMBOOT
 #endif
 
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 
-#undef CONFIG_CLOCKS_IN_MHZ
-
 /*
  * Local Bus Definitions
  */
@@ -206,7 +196,6 @@
 /* Serial Port */
 #define CONFIG_CONS_ON_SCC     /* define if console on SCC */
 #undef  CONFIG_CONS_NONE       /* define if console on something else */
-#define CONFIG_CONS_INDEX       1  /* which serial channel for console */
 
 #define CONFIG_SYS_BAUDRATE_TABLE  \
        {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
@@ -241,8 +230,6 @@
 #define CONFIG_SYS_PCI1_IO_SIZE        0x100000        /* 1M */
 
 #if defined(CONFIG_PCI)
-#undef CONFIG_EEPRO100
-#undef CONFIG_TULIP
 
 #if !defined(CONFIG_PCI_PNP)
     #define PCI_ENET0_IOADDR   0xe0000000
@@ -257,9 +244,6 @@
 
 #ifdef CONFIG_TSEC_ENET
 
-#ifndef CONFIG_MII
-#define CONFIG_MII             1       /* MII PHY management */
-#endif
 #define CONFIG_TSEC1   1
 #define CONFIG_TSEC1_NAME      "TSEC0"
 #define CONFIG_TSEC2   1
@@ -298,12 +282,6 @@
   #define FETH3_RST            0x80
 #endif                                 /* CONFIG_ETHER_INDEX */
 
-#ifndef CONFIG_MII
-#define CONFIG_MII             1       /* MII PHY management */
-#endif
-
-#define CONFIG_BITBANGMII              /* bit-bang MII PHY management */
-
 /*
  * GPIO pins used for bit-banged MII communications
  */
@@ -329,14 +307,6 @@
 /*
  * Environment
  */
-#ifndef CONFIG_SYS_RAMBOOT
-  #define CONFIG_ENV_ADDR              (CONFIG_SYS_MONITOR_BASE + 0x40000)
-  #define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
-  #define CONFIG_ENV_SIZE              0x2000
-#else
-  #define CONFIG_ENV_ADDR              (CONFIG_SYS_MONITOR_BASE - 0x1000)
-  #define CONFIG_ENV_SIZE              0x2000
-#endif
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
@@ -345,18 +315,12 @@
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
 
 #undef CONFIG_WATCHDOG                 /* watchdog disabled */
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_SYS_LONGHELP                    /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING                 /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE                   /* add autocompletion support */
 #define CONFIG_SYS_LOAD_ADDR   0x1000000       /* default load address */
 
 #define CONFIG_SYS_BARGSIZE    CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
@@ -385,7 +349,7 @@
 
 #define CONFIG_IPADDR    192.168.1.253
 
-#define CONFIG_HOSTNAME                unknown
+#define CONFIG_HOSTNAME                "unknown"
 #define CONFIG_ROOTPATH                "/nfsroot"
 #define CONFIG_BOOTFILE                "your.uImage"