/*
+ * Copyright 2004 Freescale Semiconductor.
* (C) Copyright 2002,2003 Motorola,Inc.
* Xianghua Xiao <X.Xiao@motorola.com>
*
* MA 02111-1307 USA
*/
-/* mpc8560ads board configuration file */
-/* please refer to doc/README.mpc85xx for more info */
-/* make sure you change the MAC address and other network params first,
- * search for CONFIG_ETHADDR,CONFIG_SERVERIP,etc in this file
+/*
+ * mpc8560ads board configuration file
+ *
+ * Please refer to doc/README.mpc85xx for more info.
+ *
+ * Make sure you change the MAC address and other network params first,
+ * search for CONFIG_ETHADDR, CONFIG_SERVERIP, etc in this file.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
-#define CONFIG_E500 1 /* BOOKE e500 family */
-#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
-#define CONFIG_MPC85xx_REV1 1 /* MPC85xx Rev 1.0 chip */
-#define CONFIG_MPC8560 1 /* MPC8560 specific */
-#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
-
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
-#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
+#define CONFIG_CPM2 1 /* has CPM2 */
+#define CONFIG_MPC8560ADS 1 /* MPC8560ADS board specific */
+#define CONFIG_MPC8560 1
+
+#define CONFIG_PCI
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_ETHER_ON_FCC /* cpm FCC ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-#if defined(CONFIG_MPC85xx_REV1)
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#endif
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-/* Using Localbus SDRAM to emulate flash before we can program the flash,
- * normally you need a flash-boot image(u-boot.bin), if so undef this.
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+/*
+ * sysclk for MPC85xx
+ *
+ * Two valid values are:
+ * 33000000
+ * 66000000
+ *
+ * Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
*/
-#undef CONFIG_RAM_AS_FLASH
-#if !defined(CONFIG_PCI) /* some PCI card is 33Mhz only */
-#define CONFIG_SYS_CLK_FREQ 66000000/* sysclk for MPC85xx */
-#else
-#define CONFIG_SYS_CLK_FREQ 33000000/* most pci cards are 33Mhz */
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 33000000
#endif
-#if !defined(CONFIG_SPD_EEPROM) /* manually set up DDR parameters */
-#define CONFIG_DDR_SETTING
-#endif
-/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
-#undef CONFIG_BTB /* toggle branch predition */
-#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
+#define CFG_INIT_DBCR DBCR_IDM /* Enable Debug Exceptions */
-#undef CFG_DRAM_TEST /* memory test, takes time */
-#define CFG_MEMTEST_START 0x00200000 /* memtest region */
+#define CFG_MEMTEST_START 0x00200000 /* memtest region */
#define CFG_MEMTEST_END 0x00400000
-#if (defined(CONFIG_PCI) && defined(CONFIG_TSEC_ENET) || \
- defined(CONFIG_PCI) && defined(CONFIG_ETHER_ON_FCC) || \
- defined(CONFIG_TSEC_ENET) && defined(CONFIG_ETHER_ON_FCC))
-#error "You can only use ONE of PCI Ethernet Card or TSEC Ethernet or CPM FCC."
-#endif
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xfdf00000 /* relocated CCSRBAR */
-#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
+#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
+/*
+ * DDR Setup
+ */
+#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
#else
-#define CFG_LBC_SDRAM_BASE 0xf8000000 /* Localbus SDRAM */
-#endif
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
-#else /* Boot from real Flash */
-#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
+ /*
+ * Manually set up DDR parameters
+ */
+ #define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+ #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+ #define CFG_DDR_CS0_CONFIG 0x80000002
+ #define CFG_DDR_TIMING_1 0x37344321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+ #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+ #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+ #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
#endif
-#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
-#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
+
+/*
+ * SDRAM on the Local Bus
+ */
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
+#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
+
+#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 64 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT 60000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-
-#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning*/
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR*/
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page*/
-#endif
+#define CONFIG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_FLASH_EMPTY_INFO
#undef CONFIG_CLOCKS_IN_MHZ
-/* local bus definitions */
-#define CFG_BR2_PRELIM 0xf8001861 /* 64MB localbus SDRAM */
+
+/*
+ * Local Bus Definitions
+ */
+
+/*
+ * Base Register 2 and Option Register 2 configure SDRAM.
+ * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ *
+ * For BR2, need:
+ * Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
+ * port-size = 32-bits = BR2[19:20] = 11
+ * no parity checking = BR2[21:22] = 00
+ * SDRAM for MSEL = BR2[24:26] = 011
+ * Valid = BR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
+ *
+ * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: the top 17 bits of BR2.
+ */
+
+#define CFG_BR2_PRELIM 0xf0001861
+
+/*
+ * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ *
+ * For OR2, need:
+ * 64MB mask for AM, OR2[0:7] = 1111 1100
+ * XAM, OR2[17:18] = 11
+ * 9 columns OR2[19-21] = 010
+ * 13 rows OR2[23-25] = 100
+ * EAD set for extra time OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
+ */
+
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* local bus freq */
-#define CFG_LBC_LBCR 0x00000000
-#define CFG_LBC_LSRT 0x20000000
-#define CFG_LBC_MRTPR 0x20000000
-#define CFG_LBC_LSDMR_1 0x2861b723
-#define CFG_LBC_LSDMR_2 0x0861b723
-#define CFG_LBC_LSDMR_3 0x0861b723
-#define CFG_LBC_LSDMR_4 0x1861b723
-#define CFG_LBC_LSDMR_5 0x4061b723
-
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#else
-#define CFG_BR4_PRELIM 0xfc000801 /* 32KB, 8-bit wide for ADS config reg */
-#endif
+
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x20000000 /* LB refresh timer prescal*/
+
+/*
+ * LSDMR masks
+ */
+#define CFG_LBC_LSDMR_RFEN (1 << (31 - 1))
+#define CFG_LBC_LSDMR_BSMA1516 (3 << (31 - 10))
+#define CFG_LBC_LSDMR_BSMA1617 (4 << (31 - 10))
+#define CFG_LBC_LSDMR_RFCR5 (3 << (31 - 16))
+#define CFG_LBC_LSDMR_RFCR16 (7 << (31 - 16))
+#define CFG_LBC_LSDMR_PRETOACT3 (3 << (31 - 19))
+#define CFG_LBC_LSDMR_PRETOACT7 (7 << (31 - 19))
+#define CFG_LBC_LSDMR_ACTTORW3 (3 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW7 (7 << (31 - 22))
+#define CFG_LBC_LSDMR_ACTTORW6 (6 << (31 - 22))
+#define CFG_LBC_LSDMR_BL8 (1 << (31 - 23))
+#define CFG_LBC_LSDMR_WRC2 (2 << (31 - 27))
+#define CFG_LBC_LSDMR_WRC4 (0 << (31 - 27))
+#define CFG_LBC_LSDMR_BUFCMD (1 << (31 - 29))
+#define CFG_LBC_LSDMR_CL3 (3 << (31 - 31))
+
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
+
+#define CFG_LBC_LSDMR_COMMON ( CFG_LBC_LSDMR_BSMA1516 \
+ | CFG_LBC_LSDMR_RFCR5 \
+ | CFG_LBC_LSDMR_PRETOACT3 \
+ | CFG_LBC_LSDMR_ACTTORW3 \
+ | CFG_LBC_LSDMR_BL8 \
+ | CFG_LBC_LSDMR_WRC2 \
+ | CFG_LBC_LSDMR_CL3 \
+ | CFG_LBC_LSDMR_RFEN \
+ )
+
+/*
+ * SDRAM Controller configuration sequence.
+ */
+#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_PCHALL)
+#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_ARFRSH)
+#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_MRW)
+#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
+ | CFG_LBC_LSDMR_OP_NORMAL)
+
+
+/*
+ * 32KB, 8-bit wide for ADS config reg
+ */
+#define CFG_BR4_PRELIM 0xf8000801
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
-#define CONFIG_CONS_ON_SCC /* define if console on SCC */
-#undef CONFIG_CONS_NONE /* define if console on something else */
-#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
+#define CONFIG_CONS_ON_SCC /* define if console on SCC */
+#undef CONFIG_CONS_NONE /* define if console on something else */
+#define CONFIG_CONS_INDEX 1 /* which serial channel for console */
#define CONFIG_BAUDRATE 115200
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support*/
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
-#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
-#define CFG_PCI_MEM_BASE 0xe0000000
-#define CFG_PCI_MEM_PHYS 0xe0000000
-#define CFG_PCI_MEM_SIZE 0x10000000
+/* RapidIO MMU */
+#define CFG_RIO_MEM_BASE 0xc0000000 /* base address */
+#define CFG_RIO_MEM_PHYS CFG_RIO_MEM_BASE
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 128M */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CFG_PCI1_MEM_BASE 0x80000000
+#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
+#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_IO_BASE 0x00000000
+#define CFG_PCI1_IO_PHYS 0xe2000000
+#define CFG_PCI1_IO_SIZE 0x100000 /* 1M */
+
+#if defined(CONFIG_PCI)
-#if defined(CONFIG_PCI) /* PCI Ethernet card */
#define CONFIG_NET_MULTI
-#define CONFIG_EEPRO100
-#undef CONFIG_TULIP
#define CONFIG_PCI_PNP /* do pci plug-and-play */
- #if !defined(CONFIG_PCI_PNP)
- #define PCI_ENET0_IOADDR 0xe0000000
- #define PCI_ENET0_MEMADDR 0xe0000000
- #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
- #endif
-#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
-#if defined(CONFIG_MPC85xx_REV1) /* Errata PCI 7 */
- #define CFG_PCI_SUBSYS_DEVICEID 0x0003
-#else
- #define CFG_PCI_SUBSYS_DEVICEID 0x0009
+
+#undef CONFIG_EEPRO100
+#undef CONFIG_TULIP
+
+#if !defined(CONFIG_PCI_PNP)
+ #define PCI_ENET0_IOADDR 0xe0000000
+ #define PCI_ENET0_MEMADDR 0xe0000000
+ #define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
#endif
-#elif defined(CONFIG_TSEC_ENET) /* TSEC Ethernet port */
+
+#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+
+#endif /* CONFIG_PCI */
+
+
+#ifdef CONFIG_TSEC_ENET
+
+#ifndef CONFIG_NET_MULTI
#define CONFIG_NET_MULTI 1
-#define CONFIG_PHY_M88E1011 1 /* GigaBit Ether PHY */
-#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 8 /* PHY address */
-#elif defined(CONFIG_ETHER_ON_FCC) /* CPM FCC Ethernet */
-#define CONFIG_ETHER_ON_FCC /* define if ether on FCC */
-#undef CONFIG_ETHER_NONE /* define if ether on something else */
-#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
- #if (CONFIG_ETHER_INDEX == 2)
+#endif
+
+#ifndef CONFIG_MII
+#define CONFIG_MII 1 /* MII PHY management */
+#endif
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define TSEC1_PHY_ADDR 0
+#define TSEC2_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define TSEC2_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
+
+#endif /* CONFIG_TSEC_ENET */
+
+#ifdef CONFIG_ETHER_ON_FCC /* CPM FCC Ethernet */
+
+#undef CONFIG_ETHER_NONE /* define if ether on something else */
+#define CONFIG_ETHER_INDEX 2 /* which channel for ether */
+
+#if (CONFIG_ETHER_INDEX == 2)
/*
* - Rx-CLK is CLK13
* - Tx-CLK is CLK14
* - Select bus for bd/buffers
* - Full duplex
*/
- #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
- #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
- #define CFG_CPMFCR_RAMTYPE 0
- #define CFG_FCC_PSMR (FCC_PSMR_FDE)
+ #define CFG_CMXFCR_MASK (CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
+ #define CFG_CMXFCR_VALUE (CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
+ #define CFG_CPMFCR_RAMTYPE 0
+ #define CFG_FCC_PSMR (FCC_PSMR_FDE)
#define FETH2_RST 0x01
- #elif (CONFIG_ETHER_INDEX == 3)
+#elif (CONFIG_ETHER_INDEX == 3)
/* need more definitions here for FE3 */
#define FETH3_RST 0x80
- #endif /* CONFIG_ETHER_INDEX */
-#define CONFIG_MII /* MII PHY management */
-#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+#endif /* CONFIG_ETHER_INDEX */
+
+#ifndef CONFIG_MII
+#define CONFIG_MII 1 /* MII PHY management */
+#endif
+
+#define CONFIG_BITBANGMII /* bit-bang MII PHY management */
+
/*
* GPIO pins used for bit-banged MII communications
*/
else iop->pdat &= ~0x00200000
#define MIIDELAY udelay(1)
+
#endif
-/* Environment */
+
+/*
+ * Environment
+ */
#ifndef CFG_RAMBOOT
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 128K(one sector) for env */
- #endif
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
-#define CFG_ENV_SIZE 0x2000
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
#endif
-#define CONFIG_BOOTARGS "root=/dev/nfs rw nfsroot=163.12.64.52:/localhome/r6aads/linuxppc/target ip=10.82.0.105:163.12.64.52:10.82.1.254:255.255.254.0:mpc8560ads-003:eth0:off console=ttyS0,115200"
-/*#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"*/
-#define CONFIG_BOOTCOMMAND "bootm 0xff400000 0xff700000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV | \
- CFG_CMD_LOADS ))
- #elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_I2C ) & \
- ~(CFG_CMD_ENV))
- #elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C) & \
- ~(CFG_CMD_ENV))
- #endif
-#else
- #if defined(CONFIG_PCI)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PCI | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #elif defined(CONFIG_TSEC_ENET)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_PING | \
- CFG_CMD_I2C)
- #elif defined(CONFIG_ETHER_ON_FCC)
- #define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_MII | \
- CFG_CMD_PING | CFG_CMD_I2C)
- #endif
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
+
+#if defined(CONFIG_PCI)
+ #define CONFIG_CMD_PCI
+#endif
+
+#if defined(CONFIG_ETHER_ON_FCC)
+ #define CONFIG_CMD_MII
+#endif
+
+#if defined(CFG_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
#endif
-#include <cmd_confdefs.h>
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "MPC8560ADS=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CFG_LOAD_ADDR 0x1000000 /* default load address */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if defined(CONFIG_CMD_KGDB)
+ #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+ #define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
+
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_LOAD_ADDR 0x1000000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*Note: change below for your network setting!!! */
+
+/*
+ * Environment Configuration
+ */
+
+/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
-#define CONFIG_ETHADDR 00:01:af:07:9b:8a
-#define CONFIG_ETH1ADDR 00:01:af:07:9b:8b
-#define CONFIG_ETH2ADDR 00:01:af:07:9b:8c
+#define CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
+#define CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD
+#define CONFIG_HAS_ETH2
+#define CONFIG_ETH2ADDR 00:E0:0C:00:02:FD
+#define CONFIG_HAS_ETH3
+#define CONFIG_ETH3ADDR 00:E0:0C:00:03:FD
#endif
-#define CONFIG_SERVERIP 163.12.64.52
-#define CONFIG_IPADDR 10.82.0.105
-#define CONFIG_GATEWAYIP 10.82.1.254
-#define CONFIG_NETMASK 255.255.254.0
-#define CONFIG_HOSTNAME MPC8560ADS_PILOT_003
-#define CONFIG_ROOTPATH /home/r6aads/mpclinux/eldk-2.0.2/ppc_82xx
-#define CONFIG_BOOTFILE pImage
+#define CONFIG_IPADDR 192.168.1.253
+
+#define CONFIG_HOSTNAME unknown
+#define CONFIG_ROOTPATH /nfsroot
+#define CONFIG_BOOTFILE your.uImage
+
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
+#define CONFIG_NETMASK 255.255.255.0
+
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+
+#define CONFIG_BAUDRATE 115200
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyCPM\0" \
+ "ramdiskaddr=1000000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8560ads.dtb\0"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff