#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+#define CONFIG_FSL_VIA
+#define CONFIG_FSL_CDS_EEPROM
/*
* When initializing flash, if we cannot find the manufacturer ID,
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
+#define CONFIG_FSL_CADMUS
+
#define CADMUS_BASE_ADDR 0xf8000000
#define CFG_BR3_PRELIM 0xf8000801
#define CFG_OR3_PRELIM 0xfff00ff7
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8555@0"
-#define OF_SOC "soc8555@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600"
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* I2C
#define CFG_PCI2_IO_PHYS 0xe2100000
#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
#if defined(CONFIG_PCI)
#define CONFIG_TSEC1_NAME "TSEC0"
#define CONFIG_TSEC2 1
#define CONFIG_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-#define FEC_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD