#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+#define CONFIG_FSL_VIA
+#define CONFIG_FSL_CDS_EEPROM
/*
* When initializing flash, if we cannot find the manufacturer ID,
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
+#define CONFIG_FSL_CADMUS
+
#define CADMUS_BASE_ADDR 0xf8000000
#define CFG_BR3_PRELIM 0xf8000801
#define CFG_OR3_PRELIM 0xfff00ff7
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE 8192
-
-#define OF_CPU "PowerPC,8555@0"
-#define OF_SOC "soc8555@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8555@e0000000/serial@4600"
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/*
* I2C
#define CFG_PCI2_IO_PHYS 0xe2100000
#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#ifdef CONFIG_LEGACY
+#define BRIDGE_ID 17
+#define VIA_ID 2
+#else
+#define BRIDGE_ID 28
+#define VIA_ID 4
+#endif
#if defined(CONFIG_PCI)
#endif
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_MPC85XX_TSEC1 1
-#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
-#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "TSEC0"
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "TSEC1"
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
-#define FEC_PHYIDX 0
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC2_FLAGS TSEC_GIGABIT
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+
#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_I2C \
- | CFG_CMD_MII)
+ #define CONFIG_CMD_PCI
#endif
-#include <cmd_confdefs.h>
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
#define CONFIG_ETHADDR 00:E0:0C:00:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:00:01:FD