/* DDR Setup */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_SPD
-#define CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
#endif
-#define CONFIG_SYS_BR0_PRELIM \
- (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS + 0x800000) | BR_PS_16 | BR_V)
-#define CONFIG_SYS_BR1_PRELIM \
- (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
-
-#define CONFIG_SYS_OR0_PRELIM 0xff806e65
-#define CONFIG_SYS_OR1_PRELIM 0xff806e65
-
#define CONFIG_SYS_FLASH_BANKS_LIST \
{CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
* FIXME: the top 17 bits of BR2.
*/
-#define CONFIG_SYS_BR2_PRELIM \
- (BR_PHYS_ADDR(CONFIG_SYS_LBC_SDRAM_BASE_PHYS) \
- | BR_PS_32 | (3<<BR_MSEL_SHIFT) | BR_V)
-
/*
* The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
*
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
-#define CONFIG_SYS_OR2_PRELIM 0xfc006901
-
#define CONFIG_SYS_LBC_LCRR 0x00030004 /* LB clock ratio reg */
#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
#define CONFIG_SYS_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
#else
#define CADMUS_BASE_ADDR_PHYS CADMUS_BASE_ADDR
#endif
-#define CONFIG_SYS_BR3_PRELIM \
- (BR_PHYS_ADDR(CADMUS_BASE_ADDR_PHYS) | BR_PS_8 | BR_V)
-#define CONFIG_SYS_OR3_PRELIM 0xfff00ff7
#define CONFIG_SYS_INIT_RAM_LOCK 1
#define CONFIG_SYS_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_SYS_NS16550_SERIAL
* I2C
*/
#if !CONFIG_IS_ENABLED(DM_I2C)
-#define CONFIG_SYS_I2C_LEGACY
-#define CONFIG_SYS_FSL_I2C_SPEED 400000
-#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} }
#else
#define CONFIG_SYS_SPD_BUS_NUM 0
-#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
-#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
#endif
-#define CONFIG_SYS_I2C_FSL
/* EEPROM */
-#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_CCID
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
/*
* General PCI
#endif
#if defined(CONFIG_PCI)
-
-#if !defined(CONFIG_DM_PCI)
-#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
-#define CONFIG_PCI_INDIRECT_BRIDGE 1
-#define CONFIG_SYS_PCIE1_NAME "Slot"
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
-#else
-#define CONFIG_SYS_PCIE1_MEM_BUS 0xa0000000
-#endif
-#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
-#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
-#define CONFIG_SYS_PCIE1_IO_SIZE 0x00100000 /* 1M */
-#endif
-
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-
#endif /* CONFIG_PCI */
#if defined(CONFIG_TSEC_ENET)
*/
#define CONFIG_BOOTP_BOOTFILESIZE
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/*
* For booting Linux, the board info and command line data
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#endif
-
/*
* Environment Configuration
*/
#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.255.0
-#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:ecc=off\0" \
"netdev=eth0\0" \
"fdtaddr=1e00000\0" \
"fdtfile=mpc8548cds.dtb\0"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "tftp $fdtaddr $fdtfile;" \
- "bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND
-
#endif /* __CONFIG_H */