#define CONFIG_MPC8548 1 /* MPC8548 specific */
#define CONFIG_MPC8548CDS 1 /* MPC8548CDS board specific */
-#undef CONFIG_PCI
+#define CONFIG_PCI
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
#define OF_TBCLK (bd->bi_busfreq / 8)
#define OF_STDOUT_PATH "/soc8548@e0000000/serial@4600"
-/* I2C */
-#define CONFIG_HARD_I2C /* I2C with hardware support */
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support*/
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_EEPROM_ADDR 0x57
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CFG_I2C_OFFSET 0x3000
/*
* General PCI
- * Addresses are mapped 1-1.
+ * Memory space is mapped 1-1, but I/O space must start from 0.
*/
#define CFG_PCI1_MEM_BASE 0x80000000
#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI1_IO_BASE 0x00000000
#define CFG_PCI1_IO_PHYS 0xe2000000
-#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
-#define CFG_PCI2_MEM_BASE 0xa0000000
+#define CFG_PCI2_MEM_BASE 0x90000000
#define CFG_PCI2_MEM_PHYS CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCI2_MEM_SIZE 0x10000000 /* 256M */
#define CFG_PCI2_IO_BASE 0x00000000
-#define CFG_PCI2_IO_PHYS 0xe2100000
-#define CFG_PCI2_IO_SIZE 0x00100000 /* 1M */
+#define CFG_PCI2_IO_PHYS 0xe2800000
+#define CFG_PCI2_IO_SIZE 0x00800000 /* 8M */
+#define CFG_PEX_MEM_BASE 0xa0000000
+#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
+#define CFG_PEX_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PEX_IO_BASE 0x00000000
+#define CFG_PEX_IO_PHYS 0xe3000000
+#define CFG_PEX_IO_SIZE 0x01000000 /* 16M */
+
+/*
+ * RapidIO MMU
+ */
+#define CFG_RIO_MEM_BASE 0xC0000000
+#define CFG_RIO_MEM_SIZE 0x20000000 /* 512M */
#if defined(CONFIG_PCI)
#define CONFIG_MPC85XX_TSEC2_NAME "eTSEC1"
#define CONFIG_MPC85XX_TSEC3 1
#define CONFIG_MPC85XX_TSEC3_NAME "eTSEC2"
-#define CONFIG_MPC85XX_TSEC4 1
+#undef CONFIG_MPC85XX_TSEC4
#define CONFIG_MPC85XX_TSEC4_NAME "eTSEC3"
#undef CONFIG_MPC85XX_FEC
#define TSEC2_PHY_ADDR 1
#define TSEC3_PHY_ADDR 2
#define TSEC4_PHY_ADDR 3
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define TSEC3_PHYIDX 0
#define TSEC4_PHYIDX 0
-#define FEC_PHYIDX 0
/* Options are: eTSEC[0-3] */
#define CONFIG_ETHPRIME "eTSEC0"
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS1\0" \
- "ramdiskaddr=400000\0" \
- "ramdiskfile=your.ramdisk.u-boot\0"
+ "ramdiskaddr=600000\0" \
+ "ramdiskfile=your.ramdisk.u-boot\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=your.fdt.dtb\0"
+
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \