MIPS: convert CONFIG_SYS_MIPS_TIMER_FREQ to Kconfig

[platform/kernel/u-boot.git] / include / configs / MPC8548CDS.h

diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index fc3cc0c..0951931 100644 (file)
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -16,10 +16,6 @@
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1                   /* SRIO port 1 */
 
-#define CONFIG_PCI1            /* PCI controller 1 */
-#define CONFIG_PCIE1           /* PCIE controller 1 (slot 1) */
-#undef CONFIG_PCI2
-
 #define CONFIG_INTERRUPTS              /* enable pci, srio, ddr interrupts */
 
 #ifndef __ASSEMBLY__
@@ -34,7 +30,6 @@
 /*
  * Only possible on E500 Version 2 or newer cores.
  */
-#define CONFIG_ENABLE_36BIT_PHYS       1
 
 #define CONFIG_SYS_CCSRBAR             0xe0000000
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
@@ -47,8 +42,6 @@
 #define CONFIG_SYS_DDR_SDRAM_BASE      0x00000000      /* DDR is system memory*/
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 
-#define CONFIG_DIMM_SLOTS_PER_CTLR     1
-
 /* I2C addresses of SPD EEPROMs */
 #define SPD_EEPROM_ADDRESS     0x51    /* CTLR 0 DIMM 0 */
 
@@ -131,14 +124,6 @@
 
 #define CONFIG_SYS_FLASH_BANKS_LIST \
        {CONFIG_SYS_FLASH_BASE_PHYS + 0x800000, CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_SYS_MAX_FLASH_SECT      128             /* sectors per device */
-#undef CONFIG_SYS_FLASH_CHECKSUM
-#define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
 
 #define CONFIG_HWCONFIG                        /* enable hwconfig */
 
@@ -248,8 +233,7 @@
 #define CONFIG_SYS_INIT_RAM_ADDR       0xe4010000      /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_SIZE       0x4000          /* Size of used area in RAM */
 
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_SP_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)
 
@@ -269,13 +253,8 @@
  */
 #if !CONFIG_IS_ENABLED(DM_I2C)
 #define CONFIG_SYS_I2C_NOPROBES                { {0, 0x69} }
-#else
-#define CONFIG_SYS_SPD_BUS_NUM 0
 #endif
 
-/* EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_CCID
-
 /*
  * General PCI
  * Memory space is mapped 1-1, but I/O space must start from 0.
@@ -324,18 +303,6 @@
 #endif
 #define CONFIG_SYS_SRIO1_MEM_SIZE      0x20000000      /* 512M */
 
-#ifdef CONFIG_LEGACY
-#define BRIDGE_ID 17
-#define VIA_ID 2
-#else
-#define BRIDGE_ID 28
-#define VIA_ID 4
-#endif
-
-#if defined(CONFIG_PCI)
-#define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#endif /* CONFIG_PCI */
-
 #if defined(CONFIG_TSEC_ENET)
 
 #define CONFIG_TSEC1   1
@@ -380,7 +347,6 @@
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ   (64 << 20)      /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 
 /*
  * Environment Configuration
@@ -401,15 +367,15 @@
        "netdev=eth0\0"                         \
        "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"     \
        "tftpflash=tftpboot $loadaddr $uboot; " \
-               "protect off " __stringify(CONFIG_SYS_TEXT_BASE)        \
+               "protect off " __stringify(CONFIG_TEXT_BASE)    \
                        " +$filesize; " \
-               "erase " __stringify(CONFIG_SYS_TEXT_BASE)              \
+               "erase " __stringify(CONFIG_TEXT_BASE)          \
                        " +$filesize; " \
-               "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)     \
+               "cp.b $loadaddr " __stringify(CONFIG_TEXT_BASE) \
                        " $filesize; "  \
-               "protect on " __stringify(CONFIG_SYS_TEXT_BASE)         \
+               "protect on " __stringify(CONFIG_TEXT_BASE)             \
                        " +$filesize; " \
-               "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE)    \
+               "cmp.b $loadaddr " __stringify(CONFIG_TEXT_BASE)        \
                        " $filesize\0"  \
        "consoledev=ttyS1\0"                    \
        "ramdiskaddr=2000000\0"                 \