#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
#define CONFIG_PCIE3 1 /* PCIE controler 3 (ULI bridge) */
#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
-#undef CONFIG_DDR_DLL
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
-#define CONFIG_DDR_ECC_CMD
#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
/*
*/
#define CONFIG_ASSUME_AMD_FLASH
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
-
#ifndef __ASSEMBLY__
extern unsigned long get_board_sys_clk(unsigned long dummy);
#endif
#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_CLEAR_LAW0 /* Clear LAW0 in cpu_init_r */
/*
* Only possible on E500 Version 2 or newer cores.
*/
#define CONFIG_ENABLE_36BIT_PHYS 1
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
-#define CFG_ALT_MEMTEST
#define CONFIG_PANIC_HANG /* do not reset board on panic */
/*
*/
#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
#define CFG_PCIE3_ADDR (CFG_CCSRBAR+0xb000)
-/*
- * DDR Setup
- */
-#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
+#define CFG_DDR_SDRAM_BASE 0x00000000
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 2
+/* I2C addresses of SPD EEPROMs */
#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
-/*
- * Make sure required options are set
- */
+/* Make sure required options are set */
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif
*/
#define CFG_BOOT_BLOCK 0xfc000000 /* boot TLB */
-#define CFG_LBC_CACHE_BASE 0xf0000000 /* Localbus cacheable */
-
#define CFG_FLASH_BASE 0xff800000 /* start of FLASH 8M */
#define CFG_BR0_PRELIM 0xff801001
#define CFG_OR0_PRELIM 0xff806e65
#define CFG_OR1_PRELIM 0xff806e65
-#define CFG_FLASH_BANKS_LIST {0xfe800000,CFG_FLASH_BASE}
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
+#define CFG_FLASH_QUIET_TEST
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
#undef CFG_FLASH_CHECKSUM
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
+#define PIXIS_VSPEED2 0x1d /* VELA VSpeed 2 */
+#define CFG_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/
+#define PIXIS_VSPEED2_TSEC1SER 0x2
+#define PIXIS_VSPEED2_TSEC3SER 0x1
+#define PIXIS_VCFGEN1_TSEC1SER 0x20
+#define PIXIS_VCFGEN1_TSEC3SER 0x40
/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM 1
-#define CFG_INIT_L1_LOCK 1
-#define CFG_INIT_L1_ADDR 0xf4010000 /* Initial L1 address */
-#define CFG_INIT_L1_END 0x00004000 /* End of used area in RAM */
-
-/* define to use L2SRAM as initial stack */
-#undef CONFIG_L2_INIT_RAM
-#define CFG_INIT_L2_ADDR 0xf8fc0000
-#define CFG_INIT_L2_END 0x00040000 /* End of used area in RAM */
-
-#ifdef CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_ADDR CFG_INIT_L1_ADDR
-#define CFG_INIT_RAM_END CFG_INIT_L1_END
-#else
-#define CFG_INIT_RAM_ADDR CFG_INIT_L2_ADDR
-#define CFG_INIT_RAM_END CFG_INIT_L2_END
-#endif
+#define CONFIG_L1_INIT_RAM
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0xf4010000 /* Initial L1 address */
+#define CFG_INIT_RAM_END 0x00004000 /* End of used area in RAM */
+
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
/* Serial Port - controlled on board with jumper J8
* open - index 2
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define OF_CPU "PowerPC,8544@0"
-#define OF_SOC "soc8544@e0000000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8544@e0000000/serial@4500"
+#define CFG_64BIT_STRTOUL 1
+#define CFG_64BIT_VSPRINTF 1
/* I2C */
#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
#if defined(CONFIG_PCI)
+/*PCIE video card used*/
+#define VIDEO_IO_OFFSET CFG_PCIE2_IO_PHYS
+
+/*PCI video card used*/
+/*#define VIDEO_IO_OFFSET CFG_PCI1_IO_PHYS*/
+
+/* video */
+#define CONFIG_VIDEO
+
+#if defined(CONFIG_VIDEO)
+#define CONFIG_BIOSEMU
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_ATI_RADEON_FB
+#define CONFIG_VIDEO_LOGO
+/*#define CONFIG_CONSOLE_CURSOR*/
+#define CFG_ISA_IO_BASE_ADDRESS VIDEO_IO_OFFSET
+#endif
+
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_TSEC3 1
#define CONFIG_TSEC3_NAME "eTSEC3"
+#define CONFIG_FSL_SGMII_RISER 1
+#define SGMII_RISER_PHY_OFFSET 0x1c
+
#define TSEC1_PHY_ADDR 0
#define TSEC3_PHY_ADDR 1
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_IS_IN_FLASH 1
#if CFG_MONITOR_BASE > 0xfff80000
-#define CFG_ENV_ADDR 0xfff80000
+#define CONFIG_ENV_ADDR 0xfff80000
#else
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x70000)
#endif
-#define CFG_ENV_SIZE 0x2000
-#define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
*/
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
-
/*
* Internal Definitions
*
#define CONFIG_ETHADDR 00:E0:0C:02:00:FD
#define CONFIG_HAS_ETH1
#define CONFIG_ETH1ADDR 00:E0:0C:02:01:FD
-#define CONFIG_HAS_ETH2
-#define CONFIG_ETH2ADDR 00:E0:0C:02:02:FD
-#define CONFIG_HAS_ETH3
-#define CONFIG_ETH3ADDR 00:E0:0C:02:03:FD
#endif
#define CONFIG_IPADDR 192.168.1.251
#define CONFIG_BOOTFILE 8544ds/uImage.uboot
#define CONFIG_UBOOTPATH 8544ds/u-boot.bin /* TFTP server */
-#define CONFIG_SERVERIP 192.168.0.1
-#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.1.1
+#define CONFIG_GATEWAYIP 192.168.1.1
#define CONFIG_NETMASK 255.255.0.0
#define CONFIG_LOADADDR 1000000 /*default location for tftp and bootm*/
#define CONFIG_BAUDRATE 115200
-#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
-#define PCIE_ENV \
- "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
- "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
- "pcieerr=md ${a}020 1; md ${a}e00 e;" \
- "pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
- "pci d.w $b.0 56 1;" \
- "pci d $b.0 104 1;pci d $b.0 110 1;pci d $b.0 130 1\0" \
- "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff;" \
- "pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff;" \
- "pci w $b.0 104 ffffffff; pci w $b.0 110 ffffffff;" \
- "pci w $b.0 130 ffffffff\0" \
- "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
- "pcie1regs=setenv a e000a; run pciereg\0" \
- "pcie2regs=setenv a e0009; run pciereg\0" \
- "pcie3regs=setenv a e000b; run pciereg\0" \
- "pcie1cfg=setenv b 3; run pciecfg\0" \
- "pcie2cfg=setenv b 5; run pciecfg\0" \
- "pcie3cfg=setenv b 0; run pciecfg\0" \
- "pcie1err=setenv a e000a; setenv b 3; run pcieerr\0" \
- "pcie2err=setenv a e0009; setenv b 5; run pcieerr\0" \
- "pcie3err=setenv a e000b; setenv b 0; run pcieerr\0" \
- "pcie1errc=setenv a e000a; setenv b 3; run pcieerrc\0" \
- "pcie2errc=setenv a e0009; setenv b 5; run pcieerrc\0" \
- "pcie3errc=setenv a e000b; setenv b 0; run pcieerrc\0"
-#else
-#define PCIE_ENV ""
-#endif
-
-#if defined(CONFIG_PCI1)
-#define PCI_ENV \
- "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
- "echo e;md ${a}e00 9\0" \
- "pci1regs=setenv a e0008; run pcireg\0" \
- "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
- "pci d.w $b.0 56 1\0" \
- "pcierrc=mw ${a}e00 ffffffff; mw ${a}e0c 0; pci w.b $b.0 7 ff;" \
- "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff\0" \
- "pci1err=setenv a e0008; setenv b 7; run pcierr\0" \
- "pci1errc=setenv a e0008; setenv b 7; run pcierrc\0"
-#else
-#define PCI_ENV ""
-#endif
-
-#if defined(CONFIG_TSEC_ENET)
-#define ENET_ENV \
- "enetreg1=md ${a}000 2; md ${a}010 9; md ${a}050 4; md ${a}08c 1;" \
- "md ${a}098 2\0" \
- "enetregt=echo t;md ${a}100 6; md ${a}140 2; md ${a}180 10; md ${a}200 10\0" \
- "enetregr=echo r;md ${a}300 6; md ${a}330 5; md ${a}380 10; md ${a}400 10\0" \
- "enetregm=echo mac;md ${a}500 5; md ${a}520 28;echo fifo;md ${a}a00 1;" \
- "echo mib;md ${a}680 31\0" \
- "enetreg=run enetreg1; run enetregm; run enetregt; run enetregr\0" \
- "enet1regs=setenv a e0024; run enetreg\0" \
- "enet3regs=setenv a e0026; run enetreg\0"
-#else
-#define ENET_ENV ""
-#endif
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=2000000\0" \
"ramdiskfile=8544ds/ramdisk.uboot\0" \
- "dtbaddr=c00000\0" \
- "dtbfile=8544ds/mpc8544ds.dtb\0" \
- "bdev=sda3\0" \
- "eoi=mw e00400b0 0\0" \
- "iack=md e00400a0 1\0" \
- "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
- "md ${a}e00 3; md ${a}e20 3; md ${a}e40 7; md ${a}f00 5\0" \
- "ddrregs=setenv a e0002; run ddrreg\0" \
- "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}b20 3;" \
- "md ${a}e00 1; md ${a}e60 1; md ${a}ef0 15\0" \
- "guregs=setenv a e00e0; run gureg\0" \
- "ecmreg=md ${a}000 1; md ${a}010 1; md ${a}bf8 2; md ${a}e00 6\0" \
- "ecmregs=setenv a e0001; run ecmreg\0" \
- "lawregs=md e0000c08 4b\0" \
- "lbcregs=md e0005000 36\0" \
- "dma0regs=md e0021100 12\0" \
- "dma1regs=md e0021180 12\0" \
- "dma2regs=md e0021200 12\0" \
- "dma3regs=md e0021280 12\0" \
- PCIE_ENV \
- PCI_ENV \
- ENET_ENV
-
+ "fdtaddr=c00000\0" \
+ "fdtfile=8544ds/mpc8544ds.dtb\0" \
+ "bdev=sda3\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr - $dtbaddr"
-
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#define CONFIG_RAMBOOTCOMMAND \
"setenv bootargs root=/dev/ram rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $ramdiskaddr $ramdiskfile;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr $ramdiskaddr $dtbaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
#define CONFIG_BOOTCOMMAND \
"setenv bootargs root=/dev/$bdev rw " \
"console=$consoledev,$baudrate $othbootargs;" \
"tftp $loadaddr $bootfile;" \
- "tftp $dtbaddr $dtbfile;" \
- "bootm $loadaddr - $dtbaddr"
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
#endif /* __CONFIG_H */
projects / platform / kernel / u-boot.git / blobdiff