Convert CONFIG_CMD_REGINFO to Kconfig

[platform/kernel/u-boot.git] / include / configs / MPC8544DS.h

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 96c0b11..13d4cb4 100644 (file)
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -52,7 +52,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW    CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -64,7 +63,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_SDRAM_BASE          CONFIG_SYS_DDR_SDRAM_BASE
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_NUM_DDR_CONTROLLERS     1
 #define CONFIG_DIMM_SLOTS_PER_CTLR     1
 #define CONFIG_CHIP_SELECTS_PER_CTRL   2
 
@@ -284,7 +282,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
 
 #define CONFIG_PCI_SCAN_SHOW           /* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
 #define CONFIG_SCSI_AHCI
 
 #ifdef CONFIG_SCSI_AHCI
@@ -321,21 +318,18 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define TSEC3_PHYIDX           0
 
 #define CONFIG_ETHPRIME                "eTSEC1"
-
-#define CONFIG_PHY_GIGE                1       /* Include GbE speed/duplex detection */
 #endif /* CONFIG_TSEC_ENET */
 
 /*
  * Environment
  */
-#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE   0x10000 /* 64K (one sector) */
 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
 #define CONFIG_ENV_ADDR                0xfff80000
 #else
-#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE + 0x70000)
+#define CONFIG_ENV_ADDR                (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #endif
 #define CONFIG_ENV_SIZE                0x2000
-#define CONFIG_ENV_SECT_SIZE   0x10000 /* 64K (one sector) */
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change */
@@ -349,22 +343,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_BOOTP_HOSTNAME
 
 /*
- * Command line configuration.
- */
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_REGINFO
-
-#if defined(CONFIG_PCI)
-    #define CONFIG_CMD_PCI
-    #define CONFIG_SCSI
-#endif
-
-/*
  * USB
  */
-#define CONFIG_USB_EHCI
 
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
 #define CONFIG_USB_EHCI_PCI
 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 #define CONFIG_PCI_EHCI_DEVICE                 0
@@ -425,8 +407,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 #undef CONFIG_BOOTARGS         /* the boot command will set bootargs*/
 
-#define CONFIG_BAUDRATE        115200
-
 #define        CONFIG_EXTRA_ENV_SETTINGS                               \
 "netdev=eth0\0"                                                \
 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                    \