#define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */
#define CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+#define CONFIG_FSL_VIA
+#define CONFIG_FSL_CDS_EEPROM
/*
* When initializing flash, if we cannot find the manufacturer ID,
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
-#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-
-#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
/*
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
* 1111 1111 1111 0000 0000 1111 1111 0111 = fff00ff7
*/
+#define CONFIG_FSL_CADMUS
+
#define CADMUS_BASE_ADDR 0xf8000000
#define CFG_BR3_PRELIM 0xf8000801
#define CFG_OR3_PRELIM 0xfff00ff7
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 2
#define CONFIG_MPC85XX_PCI2
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#if defined(CONFIG_TSEC_ENET)
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_MII 1 /* MII PHY management */
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions