#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41 */
+#define CONFIG_CPM2 1 /* has CPM2 */
#define CONFIG_MPC8541 1 /* MPC8541 specific */
#define CONFIG_MPC8541CDS 1 /* MPC8541CDS board specific */
#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
-#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+#undef CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
+
+#define CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
/*
* When initializing flash, if we cannot find the manufacturer ID,
#error ("CONFIG_SPD_EEPROM is required by MPC85555CDS")
#endif
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
/*
- * SDRAM on the Local Bus
+ * Local Bus Definitions
*/
-#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
+
+/*
+ * FLASH on the Local Bus
+ * Two banks, 8M each, using the CFI driver.
+ * Boot from BR0/OR0 bank at 0xff00_0000
+ * Alternate BR1/OR1 bank at 0xff80_0000
+ *
+ * BR0, BR1:
+ * Base address 0 = 0xff00_0000 = BR0[0:16] = 1111 1111 0000 0000 0
+ * Base address 1 = 0xff80_0000 = BR1[0:16] = 1111 1111 1000 0000 0
+ * Port Size = 16 bits = BRx[19:20] = 10
+ * Use GPCM = BRx[24:26] = 000
+ * Valid = BRx[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0001 0000 0000 0001 = ff801001 BR0
+ * 1111 1111 0000 0000 0001 0000 0000 0001 = ff001001 BR1
+ *
+ * OR0, OR1:
+ * Addr Mask = 8M = ORx[0:16] = 1111 1111 1000 0000 0
+ * Reserved ORx[17:18] = 11, confusion here?
+ * CSNT = ORx[20] = 1
+ * ACS = half cycle delay = ORx[21:22] = 11
+ * SCY = 6 = ORx[24:27] = 0110
+ * TRLX = use relaxed timing = ORx[29] = 1
+ * EAD = use external address latch delay = OR[31] = 1
+ *
+ * 0 4 8 12 16 20 24 28
+ * 1111 1111 1000 0000 0110 1110 0110 0101 = ff806e65 ORx
+ */
+
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 8M */
-#define CFG_BR0_PRELIM 0xff801001 /* port size 16bit */
-#define CFG_BR1_PRELIM 0xff001001 /* port size 16bit */
+#define CFG_BR0_PRELIM 0xff801001
+#define CFG_BR1_PRELIM 0xff001001
-#define CFG_OR0_PRELIM 0xff806e61 /* 8MB Flash */
-#define CFG_OR1_PRELIM 0xff806e61 /* 8MB Flash */
+#define CFG_OR0_PRELIM 0xff806e65
+#define CFG_OR1_PRELIM 0xff806e65
#define CFG_FLASH_BANKS_LIST {0xff800000, CFG_FLASH_BASE}
#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
-#undef CONFIG_CLOCKS_IN_MHZ
/*
- * Local Bus Definitions
+ * SDRAM on the Local Bus
*/
+#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
+#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
/*
* Base Register 2 and Option Register 2 configure SDRAM.
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
+#define CONFIG_MPC85XX_TSEC1_NAME "TSEC0"
#define CONFIG_MPC85XX_TSEC2 1
+#define CONFIG_MPC85XX_TSEC2_NAME "TSEC1"
#undef CONFIG_MPC85XX_FEC
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
#define FEC_PHYIDX 0
-#define CONFIG_ETHPRIME "MOTO ENET0"
+
+/* Options are: TSEC[0-1] */
+#define CONFIG_ETHPRIME "TSEC0"
#endif /* CONFIG_TSEC_ENET */
projects / platform / kernel / u-boot.git / blobdiff