#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
-#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_BOOKE 1 /* BOOKE */
#define CONFIG_E500 1 /* BOOKE e500 family */
#define CONFIG_MPC85xx 1 /* MPC8540/MPC8560 */
#define CONFIG_MPC8540 1 /* MPC8540 specific */
#define CONFIG_MPC8540EVAL 1 /* MPC8540EVAL board specific */
-#undef CONFIG_PCI /* pci ethernet support */
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#undef CONFIG_PCI /* pci ethernet support */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#undef CONFIG_DDR_ECC /* only for ECC DDR module */
#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
/* Using Localbus SDRAM to emulate flash before we can program the flash,
* normally you only need a flash-boot image(u-boot.bin),if unsure undef this.
* Not availabe for EVAL board
#endif
/* below can be toggled for performance analysis. otherwise use default */
-#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
#undef CONFIG_BTB /* toggle branch predition */
#undef CONFIG_ADDR_STREAMING /* toggle addr streaming */
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
-#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms)*/
#define CFG_FLASH_CFI 1
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#define CFG_NS16550_SERIAL
#define CFG_NS16550_REG_SIZE 1
#define CFG_NS16550_CLK get_bus_freq(0)
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
#define CONFIG_NET_MULTI
#undef CONFIG_EEPRO100
#define CONFIG_TULIP
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#if !defined(CONFIG_PCI_PNP)
#define PCI_ENET0_IOADDR 0xe0000000
#define PCI_ENET0_MEMADDR 0xe0000000
-#define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
+#define PCI_IDSEL_NUMBER 0x0c /*slot0->3(IDSEL)=12->15*/
#endif
#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
#define CFG_PCI_SUBSYS_DEVICEID 0x0008
#elif defined(CONFIG_TSEC_ENET)
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_TSEC1 1
#define CONFIG_HAS_ETH0
#define INTEL_LXT971_PHY 1
#endif
-#undef DEBUG
-
/* Environment */
#ifndef CFG_RAMBOOT
#if defined(CONFIG_RAM_AS_FLASH)
#define CONFIG_BOOTARGS "root=/dev/ram rw console=ttyS0,115200"
#define CONFIG_BOOTCOMMAND "bootm 0xff800000 0xffa00000"
-#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
+#define CONFIG_BOOTDELAY 3 /* -1 disable autoboot */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* Internal Definitions