#define CONFIG_DDR_DLL /* possible DLL fix needed */
#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
-/*
- * Use Localbus SDRAM to emulate flash before we can program the flash.
- * Normally you need a flash-boot image(u-boot.bin).
- * If unsure #undef this.
- */
-#undef CONFIG_RAM_AS_FLASH
/*
* sysclk for MPC85xx
* 66000000
*
* Most PCI cards are still 33Mhz, so in the presence of PCI, 33MHz
- * is likely the desired value here. The board, however, can run and
- * defaults to 66Mhz. In any event, this value must match the settings
- * of SW15[1] and SW17[8], and likely SW6[0:1], the SYSCLK as well.
- *
- * SW17[8] ------+ SW6
- * SW15[1] ----+ | [0:1]
- * V V V V
- * 33MHz 1 1 1 0
- * 66MHz 0 0 0 1
+ * is likely the desired value here, so that is now the default.
+ * The board, however, can run at 66MHz. In any event, this value
+ * must match the settings of some switches. Details can be found
+ * in the README.mpc85xxads.
*/
-#define CONFIG_SYS_CLK_FREQ 66000000
-
-
-#if !defined(CONFIG_SPD_EEPROM)
-#define CONFIG_DDR_SETTING /* manually set up DDR parameters */
+#ifndef CONFIG_SYS_CLK_FREQ
+#define CONFIG_SYS_CLK_FREQ 33000000
#endif
+
/*
* These can be toggled for performance analysis, otherwise use default.
*/
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
+
+/*
+ * DDR Setup
+ */
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+
+#if defined(CONFIG_SPD_EEPROM)
+ /*
+ * Determine DDR configuration from I2C interface.
+ */
+ #define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+
+#else
+ /*
+ * Manually set up DDR parameters
+ */
+ #define CFG_SDRAM_SIZE 128 /* DDR is 128MB */
+ #define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
+ #define CFG_DDR_CS0_CONFIG 0x80000002
+ #define CFG_DDR_TIMING_1 0x37344321
+ #define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
+ #define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
+ #define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
+ #define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
+#endif
+
/*
* SDRAM on the Local Bus
*/
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_LBC_SDRAM_BASE 0xfc000000 /* Localbus SDRAM */
-#else
#define CFG_LBC_SDRAM_BASE 0xf0000000 /* Localbus SDRAM */
-#endif
#define CFG_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH 16M */
-#define CFG_BR0_PRELIM 0xf8001801 /* port size 32bit */
-#else /* Boot from real Flash */
#define CFG_FLASH_BASE 0xff000000 /* start of FLASH 16M */
#define CFG_BR0_PRELIM 0xff001801 /* port size 32bit */
-#endif
#define CFG_OR0_PRELIM 0xff006ff7 /* 16MB Flash */
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
#undef CFG_RAMBOOT
#endif
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
#undef CONFIG_CLOCKS_IN_MHZ
-#if defined(CONFIG_DDR_SETTING)
-#define CFG_DDR_CS0_BNDS 0x00000007 /* 0-128MB */
-#define CFG_DDR_CS0_CONFIG 0x80000002
-#define CFG_DDR_TIMING_1 0x37344321
-#define CFG_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
-#define CFG_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
-#define CFG_DDR_MODE 0x00000062 /* DLL,normal,seq,4/2.5 */
-#define CFG_DDR_INTERVAL 0x05200100 /* autocharge,no open page */
-#endif
-
/*
* Local Bus Definitions
* SDRAM Controller configuration sequence.
*/
#define CFG_LBC_LSDMR_1 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_PCHALL) /*0x2861b723*/
+ | CFG_LBC_LSDMR_OP_PCHALL)
#define CFG_LBC_LSDMR_2 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_3 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_ARFRSH) /*0x0861b723*/
+ | CFG_LBC_LSDMR_OP_ARFRSH)
#define CFG_LBC_LSDMR_4 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_MRW) /*0x1861b723*/
+ | CFG_LBC_LSDMR_OP_MRW)
#define CFG_LBC_LSDMR_5 ( CFG_LBC_LSDMR_COMMON \
- | CFG_LBC_LSDMR_OP_NORMAL) /*0x4061b723*/
+ | CFG_LBC_LSDMR_OP_NORMAL)
-#if defined(CONFIG_RAM_AS_FLASH)
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#else
-#define CFG_BR4_PRELIM 0xf8000801 /* 32KB, 8-bit wide for ADS config reg */
-#endif
+/*
+ * 32KB, 8-bit wide for ADS config reg
+ */
+#define CFG_BR4_PRELIM 0xf8000801
#define CFG_OR4_PRELIM 0xffffe1f1
#define CFG_BCSR (CFG_BR4_PRELIM & 0xffff8000)
#define CONFIG_L1_INIT_RAM
#define CFG_INIT_RAM_LOCK 1
-#define CFG_INIT_RAM_ADDR 0x40000000 /* Initial RAM address */
+#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_MPC85XX_TSEC1 1
#define CONFIG_MPC85XX_TSEC2 1
-#define CONFIG_MPC85XX_FEC 1
#define TSEC1_PHY_ADDR 0
#define TSEC2_PHY_ADDR 1
-#define FEC_PHY_ADDR 3
#define TSEC1_PHYIDX 0
#define TSEC2_PHYIDX 0
+
+#define CONFIG_MPC85XX_FEC 1
+#define FEC_PHY_ADDR 3
#define FEC_PHYIDX 0
+
#define CONFIG_ETHPRIME "MOTO ENET0"
#endif /* CONFIG_TSEC_ENET */
* Environment
*/
#ifndef CFG_RAMBOOT
- #if defined(CONFIG_RAM_AS_FLASH)
- #define CFG_ENV_IS_NOWHERE
- #define CFG_ENV_ADDR (CFG_FLASH_BASE + 0x100000)
- #define CFG_ENV_SIZE 0x2000
- #else
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
- #endif
#define CFG_ENV_SIZE 0x2000
#else
-#define CFG_NO_FLASH 1 /* Flash is not usable now */
-#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
-#define CFG_ENV_SIZE 0x2000
+ #define CFG_NO_FLASH 1 /* Flash is not usable now */
+ #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
+ #define CFG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT) || defined(CONFIG_RAM_AS_FLASH)
+#if defined(CFG_RAMBOOT)
#if defined(CONFIG_PCI)
#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
| CFG_CMD_PING \
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
-/*****************************/
-/* Environment Configuration */
-/*****************************/
+
+/*
+ * Environment Configuration
+ */
/* The mac addresses for all ethernet interface */
#if defined(CONFIG_TSEC_ENET)
#define CONFIG_BAUDRATE 115200
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"consoledev=ttyS0\0" \
"ramdiskaddr=400000\0" \
"ramdiskfile=your.ramdisk.u-boot\0"
-#define CONFIG_NFSBOOTCOMMAND \
+#define CONFIG_NFSBOOTCOMMAND \
"setenv bootargs root=/dev/nfs rw " \
"nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
projects / platform / kernel / u-boot.git / blobdiff