#define CONFIG_PCI 1
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ */
+#define CONFIG_TSEC_ENET /* TSEC Ethernet support */
+#define CONFIG_VSC7385_ENET
+
/*
* System Clock Setup
*/
/* System Clock Configuration Register */
#define CFG_SCCR_TSEC1CM 1 /* eTSEC1 clock mode (0-3) */
#define CFG_SCCR_TSEC2CM 1 /* eTSEC2 clock mode (0-3) */
-#define CFG_SCCR_SATACM SCCR_SATACM_1 /* SATA1-4 clock mode (0-3) */
+#define CFG_SCCR_SATACM SCCR_SATACM_2 /* SATA1-4 clock mode (0-3) */
/*
* System IO Config
#define CFG_IMMR 0xE0000000
/*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC2
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE 0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE 8192
+
+#endif
+
+/*
* DDR Setup
*/
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
* FLASH on the Local Bus
*/
#define CFG_FLASH_CFI /* use the Common Flash Interface */
-#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
+#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
#define CFG_FLASH_SIZE 8 /* max FLASH size is 32M */
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+/*
+ * NAND Flash on the Local Bus
+ */
+#define CFG_NAND_BASE 0xE0600000 /* 0xE0600000 */
+#define CFG_BR1_PRELIM (CFG_NAND_BASE | \
+ (2 << BR_DECC_SHIFT) | /* Use HW ECC */ \
+ BR_PS_8 | /* Port Size = 8 bit */ \
+ BR_MS_FCM | /* MSEL = FCM */ \
+ BR_V) /* valid */
+#define CFG_OR1_PRELIM (0xFFFF8000 | /* length 32K */ \
+ OR_FCM_CSCT | \
+ OR_FCM_CST | \
+ OR_FCM_CHT | \
+ OR_FCM_SCY_1 | \
+ OR_FCM_TRLX | \
+ OR_FCM_EHTR)
+#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
+#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+
+/* Vitesse 7385 */
+
#define CFG_VSC7385_BASE 0xF0000000
-/* VSC7385 Gigabit Switch support */
-#define CONFIG_VSC7385_ENET
+#ifdef CONFIG_VSC7385_ENET
+
#define CFG_BR2_PRELIM 0xf0000801 /* Base address */
#define CFG_OR2_PRELIM 0xfffe09ff /* 128K bytes*/
#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE /* Access Base */
#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access Size 128K */
+#endif
+
/*
* Serial Port
*/
#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+/* SERDES */
+#define CONFIG_FSL_SERDES
+#define CONFIG_FSL_SERDES1 0xe3000
+#define CONFIG_FSL_SERDES2 0xe3100
+
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
#ifdef CFG_HUSH_PARSER
/* Pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#define CFG_PCI_MMIO_BASE 0x90000000
#define CFG_PCI_MMIO_PHYS CFG_PCI_MMIO_BASE
#define CFG_PCI_MMIO_SIZE 0x10000000 /* 256M */
-#define CFG_PCI_IO_BASE 0xE0300000
+#define CFG_PCI_IO_BASE 0x00000000
#define CFG_PCI_IO_PHYS 0xE0300000
#define CFG_PCI_IO_SIZE 0x100000 /* 1M */
#define CONFIG_NET_MULTI
#define CONFIG_PCI_PNP /* do pci plug-and-play */
-#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
/*
* TSEC
*/
-#define CONFIG_TSEC_ENET /* TSEC ethernet support */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+#ifdef CONFIG_TSEC_ENET
-/*
- * TSEC ethernet configuration
- */
-#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_TSEC1 1
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII /* MII PHY management */
+
+#define CONFIG_TSEC1
+
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "TSEC1"
+#define CFG_TSEC1_OFFSET 0x24000
#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 0x1c
#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
+#endif
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME "TSEC1"
+#define CFG_TSEC2_OFFSET 0x25000
+#define TSEC2_PHY_ADDR 0x1c
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHYIDX 0
+#endif
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC0"
+#endif
+
+/*
+ * SATA
+ */
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CFG_SATA_MAX_DEVICE 2
+#define CONFIG_SATA1
+#define CFG_SATA1_OFFSET 0x18000
+#define CFG_SATA1 (CFG_IMMR + CFG_SATA1_OFFSET)
+#define CFG_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_SATA2
+#define CFG_SATA2_OFFSET 0x19000
+#define CFG_SATA2 (CFG_IMMR + CFG_SATA2_OFFSET)
+#define CFG_SATA2_FLAGS FLAGS_DMA
+
+#ifdef CONFIG_FSL_SATA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
/*
* Environment
*/
#ifndef CFG_RAMBOOT
- #define CFG_ENV_IS_IN_FLASH 1
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN)
- #define CFG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
- #define CFG_ENV_SIZE 0x4000
+ #define CONFIG_ENV_IS_IN_FLASH 1
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE+CFG_MONITOR_LEN)
+ #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K (one sector) for env */
+ #define CONFIG_ENV_SIZE 0x4000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
- #define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
- #define CFG_ENV_ADDR (CFG_MONITOR_BASE-0x1000)
- #define CFG_ENV_SIZE 0x2000
+ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
+ #define CONFIG_ENV_ADDR (CFG_MONITOR_BASE-0x1000)
+ #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
* MMU Setup
*/
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* DDR: cache cacheable */
#define CFG_SDRAM_LOWER CFG_SDRAM_BASE
#define CFG_SDRAM_UPPER (CFG_SDRAM_BASE + 0x10000000)
*/
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_HAS_ETH0 /* add support for "ethaddr" */
-#define CONFIG_ETHADDR 00:04:9f:ef:04:01
-#define CONFIG_HAS_ETH1 /* add support for "eth1addr" */
-#define CONFIG_ETH1ADDR 00:04:9f:ef:04:02
+#ifdef CONFIG_HAS_ETH0
+#define CONFIG_ETHADDR 00:04:9f:ef:04:01
+#endif
+
+#ifdef CONFIG_HAS_ETH1
+#define CONFIG_ETH1ADDR 00:04:9f:ef:04:02
+#endif
+
+#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_SERVERIP 10.0.0.1
#define CONFIG_RAMDISKFILE rootfs.ext2.gz.uboot
#define CONFIG_BOOTFILE uImage
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
-#define CONFIG_FDTFILE mpc837x_rdb.dtb
+#define CONFIG_FDTFILE mpc8379_rdb.dtb
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200