*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define CONFIG_MPC83XX 1 /* MPC83XX family */
#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
#define CONFIG_MPC8360EMDS 1 /* MPC8360EMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
/*
* System Clock Setup
#define CFG_SICRL 0x40000000
#define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
/*
* IMMR new address
*/
-#define CFG_IMMRBAR 0xE0000000
+#define CFG_IMMR 0xE0000000
/*
* DDR Setup
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory */
#define CFG_SDRAM_BASE CFG_DDR_BASE
#define CFG_DDR_SDRAM_BASE CFG_DDR_BASE
+#define CFG_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \
+ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#undef CONFIG_DDR_ECC /* only for ECC DDR module */
+#define CFG_83XX_DDR_USES_CS0
+
+#define CONFIG_DDR_ECC /* support DDR ECC function */
#define CONFIG_DDR_ECC_CMD /* Use DDR ECC user commands */
+/*
+ * DDRCDR - DDR Control Driver Register
+ */
+#define CFG_DDRCDR_VALUE 0x80080001
+
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
#if defined(CONFIG_SPD_EEPROM)
/*
* Manually set up DDR parameters
*/
#define CFG_DDR_SIZE 256 /* MB */
+#if defined(CONFIG_DDR_II)
+#define CFG_DDRCDR 0x80080001
+#define CFG_DDR_CS0_BNDS 0x0000000f
+#define CFG_DDR_CS0_CONFIG 0x80330102
+#define CFG_DDR_TIMING_0 0x00220802
+#define CFG_DDR_TIMING_1 0x38357322
+#define CFG_DDR_TIMING_2 0x2f9048c8
+#define CFG_DDR_TIMING_3 0x00000000
+#define CFG_DDR_CLK_CNTL 0x02000000
+#define CFG_DDR_MODE 0x47d00432
+#define CFG_DDR_MODE2 0x8000c000
+#define CFG_DDR_INTERVAL 0x03cf0080
+#define CFG_DDR_SDRAM_CFG 0x43000000
+#define CFG_DDR_SDRAM_CFG2 0x00401000
+#else
#define CFG_DDR_CONFIG (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9)
#define CFG_DDR_TIMING_1 0x37344321 /* tCL-tRCD-tRP-tRAS=2.5-3-3-7 */
#define CFG_DDR_TIMING_2 0x00000800 /* may need tuning */
-#define CFG_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */
+#define CFG_DDR_CONTROL 0x42008000 /* Self refresh,2T timing */
#define CFG_DDR_MODE 0x20000162 /* DLL,normal,seq,4/2.5 */
#define CFG_DDR_INTERVAL 0x045b0100 /* page mode */
#endif
+#endif
/*
* Memory test
#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
#define CFG_RAMBOOT
#else
-#undef CFG_RAMBOOT
+#undef CFG_RAMBOOT
#endif
#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
#define CFG_FLASH_CFI /* use the Common Flash Interface */
#define CFG_FLASH_CFI_DRIVER /* use the CFI driver */
#define CFG_FLASH_BASE 0xFE000000 /* FLASH base address */
-#define CFG_FLASH_SIZE 16 /* FLASH size is 16M */
+#define CFG_FLASH_SIZE 32 /* max FLASH size is 32M */
#define CFG_LBLAWBAR0_PRELIM CFG_FLASH_BASE /* Window base at flash base */
#define CFG_LBLAWAR0_PRELIM 0x80000018 /* 32MB window size */
#define CFG_BR0_PRELIM (CFG_FLASH_BASE | /* Flash Base address */ \
(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
BR_V) /* valid */
-#define CFG_OR0_PRELIM 0xfe006ff7 /* 16MB Flash size */
+#define CFG_OR0_PRELIM ((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+ OR_GPCM_CSNT | OR_GPCM_ACS_0b11 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
+ OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
-#define CFG_MAX_FLASH_SECT 128 /* sectors per device */
+#define CFG_MAX_FLASH_SECT 256 /* max sectors per device */
#undef CFG_FLASH_CHECKSUM
*/
#define CFG_BCSR 0xF8000000
#define CFG_LBLAWBAR1_PRELIM CFG_BCSR /* Access window base at BCSR base */
-#define CFG_LBLAWAR1_PRELIM 0x8000000E /* Access window size 32K */
+#define CFG_LBLAWAR1_PRELIM 0x8000000F /* Access window size 64K */
#define CFG_BR1_PRELIM (CFG_BCSR|0x00000801) /* Port size=8bit, MSEL=GPCM */
#define CFG_OR1_PRELIM 0xFFFFE9f7 /* length 32K */
* SDRAM for MSEL = BR2[24:26] = 011
* Valid = BR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
*
* CFG_LBC_SDRAM_BASE should be masked and OR'ed into
* 64MB mask for AM, OR2[0:7] = 1111 1100
* XAM, OR2[17:18] = 11
* 9 columns OR2[19-21] = 010
- * 13 rows OR2[23-25] = 100
+ * 13 rows OR2[23-25] = 100
* EAD set for extra time OR[31] = 1
*
- * 0 4 8 12 16 20 24 28
+ * 0 4 8 12 16 20 24 28
* 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
*/
/*
* LSDMR masks
*/
-#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_NORMAL (0 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ARFRSH (1 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_SRFRSH (2 << (31 - 4))
#define CFG_LBC_LSDMR_OP_MRW (3 << (31 - 4))
#define CFG_LBC_LSDMR_OP_PRECH (4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_PCHALL (5 << (31 - 4))
+#define CFG_LBC_LSDMR_OP_ACTBNK (6 << (31 - 4))
#define CFG_LBC_LSDMR_OP_RWINV (7 << (31 - 4))
#define CFG_LBC_LSDMR_COMMON 0x0063b723
/*
* Windows to access PIB via local bus
*/
-#define CFG_LBLAWBAR3_PRELIM 0xf8008000 /* windows base 0xf8008000 */
-#define CFG_LBLAWAR3_PRELIM 0x8000000f /* windows size 64KB */
+#define CFG_LBLAWBAR3_PRELIM 0xf8010000 /* windows base 0xf8010000 */
+#define CFG_LBLAWAR3_PRELIM 0x8000000e /* windows size 32KB */
/*
* CS4 on Local Bus, to PIB
*/
-#define CFG_BR4_PRELIM 0xf8008801 /* CS4 base address at 0xf8008000 */
+#define CFG_BR4_PRELIM 0xf8010801 /* CS4 base address at 0xf8010000 */
#define CFG_OR4_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
/*
* CS5 on Local Bus, to PIB
*/
-#define CFG_BR5_PRELIM 0xf8010801 /* CS5 base address at 0xf8010000 */
+#define CFG_BR5_PRELIM 0xf8008801 /* CS5 base address at 0xf8008000 */
#define CFG_OR5_PRELIM 0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
/*
#define CFG_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
-#define CFG_NS16550_COM1 (CFG_IMMRBAR+0x4500)
-#define CFG_NS16550_COM2 (CFG_IMMRBAR+0x4600)
+#define CFG_NS16550_COM1 (CFG_IMMR+0x4500)
+#define CFG_NS16550_COM2 (CFG_IMMR+0x4600)
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
/* Use the HUSH parser */
#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
+#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#endif
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#undef CONFIG_OF_FLAT_TREE
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_HAS_BD_T 1
+#define CONFIG_OF_HAS_UBOOT_ENV 1
+
+#define OF_CPU "PowerPC,8360@0"
+#define OF_SOC "soc8360@e0000000"
+#define OF_QE "qe@e0100000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc8360@e0000000/serial@4500"
+
/* I2C */
#define CONFIG_HARD_I2C /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CFG_I2C_SPEED 0x3F /* I2C speed and slave address */
+#define CONFIG_FSL_I2C
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
#define CFG_I2C_SLAVE 0x7F
#define CFG_I2C_NOPROBES {0x52} /* Don't probe these addrs */
#define CFG_I2C_OFFSET 0x3000
-#define CFG_I2C2_OFFSET 0x3100
+#define CFG_I2C2_OFFSET 0x3100
/*
* Config on-board RTC
#undef CONFIG_EEPRO100
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
+#define CFG_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */
#endif /* CONFIG_PCI */
#endif
/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_UEC_ETH
+#define CONFIG_ETHPRIME "Freescale GETH"
+#define CONFIG_PHY_MODE_NEED_CHANGE
+
+#define CONFIG_UEC_ETH1 /* GETH1 */
+
+#ifdef CONFIG_UEC_ETH1
+#define CFG_UEC1_UCC_NUM 0 /* UCC1 */
+#define CFG_UEC1_RX_CLK QE_CLK_NONE
+#define CFG_UEC1_TX_CLK QE_CLK9
+#define CFG_UEC1_ETH_TYPE GIGA_ETH
+#define CFG_UEC1_PHY_ADDR 0
+#define CFG_UEC1_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+#define CONFIG_UEC_ETH2 /* GETH2 */
+
+#ifdef CONFIG_UEC_ETH2
+#define CFG_UEC2_UCC_NUM 1 /* UCC2 */
+#define CFG_UEC2_RX_CLK QE_CLK_NONE
+#define CFG_UEC2_TX_CLK QE_CLK4
+#define CFG_UEC2_ETH_TYPE GIGA_ETH
+#define CFG_UEC2_PHY_ADDR 1
+#define CFG_UEC2_INTERFACE_MODE ENET_1000_GMII
+#endif
+
+/*
* Environment
*/
#ifndef CFG_RAMBOOT
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
- #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+ #define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
#define CFG_ENV_SIZE 0x2000
#else
#define CFG_NO_FLASH 1 /* Flash is not usable now */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
-#if defined(CFG_RAMBOOT)
-#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_ASKENV \
- | CFG_CMD_PCI \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_ASKENV \
- | CFG_CMD_I2C) \
- & \
- ~(CFG_CMD_ENV \
- | CFG_CMD_LOADS))
-#endif
-#else
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ASKENV
+
#if defined(CONFIG_PCI)
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PCI \
- | CFG_CMD_PING \
- | CFG_CMD_ASKENV \
- | CFG_CMD_I2C)
-#else
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
- | CFG_CMD_PING \
- | CFG_CMD_ASKENV \
- | CFG_CMD_I2C )
+ #define CONFIG_CMD_PCI
#endif
+
+#if defined(CFG_RAMBOOT)
+ #undef CONFIG_CMD_ENV
+ #undef CONFIG_CMD_LOADS
#endif
-#include <cmd_confdefs.h>
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
*/
#define CFG_DCACHE_SIZE 32768
#define CFG_CACHELINE_SIZE 32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value */
#endif
#define CFG_DBAT0U CFG_IBAT0U
/* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CFG_IBAT1L (CFG_IMMRBAR | BATL_PP_10 | \
+#define CFG_IBAT1L (CFG_IMMR | BATL_PP_10 | \
BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT1U (CFG_IMMRBAR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CFG_IBAT1U (CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
#define CFG_DBAT1L CFG_IBAT1L
#define CFG_DBAT1U CFG_IBAT1U
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#if defined(CONFIG_UEC_ETH)
#define CONFIG_ETHADDR 00:04:9f:ef:01:01
#define CONFIG_HAS_ETH1
-#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
+#define CONFIG_ETH1ADDR 00:04:9f:ef:01:02
#endif
-#define CONFIG_BAUDRATE 115200
+#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
-#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
-#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
+#define CONFIG_BOOTDELAY 6 /* -1 disables auto-boot */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=eth0\0" \
- "consoledev=ttyS0\0" \
- "ramdiskaddr=400000\0" \
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=1000000\0" \
"ramdiskfile=ramfs.83xx\0" \
+ "fdtaddr=400000\0" \
+ "fdtfile=mpc8360emds.dtb\0" \
+ ""
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $ramdiskaddr $ramdiskfile;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
-#define CONFIG_NFSBOOTCOMMAND \
- "setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$serverip:$rootpath " \
- "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr"
-
-#define CONFIG_RAMBOOTCOMMAND \
- "setenv bootargs root=/dev/ram rw " \
- "console=$consoledev,$baudrate $othbootargs;" \
- "tftp $ramdiskaddr $ramdiskfile;" \
- "tftp $loadaddr $bootfile;" \
- "bootm $loadaddr $ramdiskaddr"
#define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND