qong: enable support for compressed images

[platform/kernel/u-boot.git] / include / configs / MPC8349EMDS.h

diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index bf28d9e..541d2f4 100644 (file)
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2006
+ * (C) Copyright 2006-2010
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * See file CREDITS for list of people who contributed to this
@@ -38,8 +38,10 @@
 #define CONFIG_MPC8349         1       /* MPC8349 specific */
 #define CONFIG_MPC8349EMDS     1       /* MPC8349EMDS board specific */
 
-#define PCI_66M
-#ifdef PCI_66M
+#define        CONFIG_SYS_TEXT_BASE    0xFE000000
+
+#define CONFIG_PCI_66M
+#ifdef CONFIG_PCI_66M
 #define CONFIG_83XX_CLKIN      66000000        /* in Hz */
 #else
 #define CONFIG_83XX_CLKIN      33000000        /* in Hz */
@@ -51,7 +53,7 @@
 #endif /* CONFIG_PCISLAVE */
 
 #ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
+#ifdef CONFIG_PCI_66M
 #define CONFIG_SYS_CLK_FREQ    66000000
 #define HRCWL_CSB_TO_CLKIN     HRCWL_CSB_TO_CLKIN_4X1
 #else
@@ -76,6 +78,22 @@
 #define CONFIG_SPD_EEPROM              /* use SPD EEPROM for DDR setup*/
 
 /*
+ * define CONFIG_FSL_DDR2 to use unified DDR driver
+ * undefine it to use old spd_sdram.c
+ */
+#define CONFIG_FSL_DDR2
+#ifdef CONFIG_FSL_DDR2
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS1    0x52
+#define SPD_EEPROM_ADDRESS2    0x51
+#define CONFIG_NUM_DDR_CONTROLLERS     1
+#define CONFIG_DIMM_SLOTS_PER_CTLR     2
+#define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE  0xDeadBeef
+#endif
+
+/*
  * 32-bit data path mode.
  *
  * Please note that using this mode for devices with the real density of 64-bit
@@ -172,7 +190,7 @@
 #define CONFIG_SYS_FLASH_ERASE_TOUT    60000   /* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT    500     /* Flash Write Timeout (ms) */
 
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE       /* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
@@ -191,10 +209,9 @@
 
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xFD000000              /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END        0x1000                  /* End of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000                  /* Size of used area in RAM*/
 
-#define CONFIG_SYS_GBL_DATA_SIZE       0x100                   /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 #define CONFIG_SYS_MONITOR_LEN         (384 * 1024)            /* Reserve 384 kB for Mon */
@@ -283,7 +300,6 @@
  * Serial Port
  */
 #define CONFIG_CONS_INDEX     1
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
@@ -296,6 +312,7 @@
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
 
 #define CONFIG_CMDLINE_EDITING 1       /* add command line history     */
+#define CONFIG_AUTO_COMPLETE           /* add autocompletion support   */
 /* Use the HUSH parser */
 #define CONFIG_SYS_HUSH_PARSER
 #ifdef  CONFIG_SYS_HUSH_PARSER
@@ -369,7 +386,6 @@
 #undef PCI_ONE_PCI1
 #endif
 
-#define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP         /* do pci plug-and-play */
 #define CONFIG_83XX_PCI_STREAMING
 
@@ -393,9 +409,6 @@
 #define CONFIG_TSEC_ENET               /* TSEC ethernet support */
 
 #if defined(CONFIG_TSEC_ENET)
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI       1
-#endif
 
 #define CONFIG_GMII            1       /* MII PHY management */
 #define CONFIG_TSEC1   1
@@ -495,10 +508,10 @@
 
 /*
  * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
+ * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CONFIG_SYS_BOOTMAPSZ   (8 << 20)       /* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ   (256 << 20)     /* Initial Memory map for Linux*/
 
 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
@@ -597,7 +610,8 @@
 #define CONFIG_SYS_SICRL SICRL_LDP_A
 
 #define CONFIG_SYS_HID0_INIT   0x000000000
-#define CONFIG_SYS_HID0_FINAL  HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID0_FINAL  (HID0_ENABLE_MACHINE_CHECK | \
+                                HID0_ENABLE_INSTRUCTION_CACHE)
 
 /* #define CONFIG_SYS_HID0_FINAL               (\
        HID0_ENABLE_INSTRUCTION_CACHE |\
@@ -666,14 +680,6 @@
 #define CONFIG_SYS_DBAT7L      CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U      CONFIG_SYS_IBAT7U
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01    /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02    /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */
@@ -690,8 +696,8 @@
 #endif
 
 #define CONFIG_HOSTNAME                mpc8349emds
-#define CONFIG_ROOTPATH                /nfsroot/rootfs
-#define CONFIG_BOOTFILE                uImage
+#define CONFIG_ROOTPATH                "/nfsroot/rootfs"
+#define CONFIG_BOOTFILE                "uImage"
 
 #define CONFIG_LOADADDR                800000  /* default location for tftp and bootm */