#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
#endif
+#include <linux/stringify.h>
#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_ELBC 1
/*
* On-board devices
#define CONFIG_VSC7385_ENET
#define CONFIG_TSEC2
-#define CONFIG_SYS_IMMR 0xE0000000
-
-#define CONFIG_SYS_MEMTEST_START 0x00001000
-#define CONFIG_SYS_MEMTEST_END 0x07f00000
-
/* Early revs of this board will lock up hard when attempting
* to access the PMC registers, unless a JTAG debugger is
* connected, or some resistor modifications are made.
*/
#define CONFIG_SYS_8313ERDB_BROKEN_PMC 1
-#define CONFIG_SYS_ACR_PIPE_DEP 3 /* Arbiter pipeline depth (0-3) */
-#define CONFIG_SYS_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
-
/*
* Device configurations
*/
/*
* DDR Setup
*/
-#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
-#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/
/*
* Manually set up DDR parameters, as this board does not
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use h/w Flash protection. */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* display empty sectors */
-#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \
- | BR_PS_16 /* 16 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_9 \
- | OR_GPCM_EHTR \
- | OR_GPCM_EAD)
- /* 0xFF006FF7 TODO SLOW 16 MB flash size */
-
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
#define CONFIG_SYS_MAX_FLASH_SECT 135 /* sectors per device */
#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */
#define CONFIG_SYS_MALLOC_LEN (512 * 1024) /* Reserved for malloc */
-/*
- * Local Bus LCRR and LBCR regs
- */
-#define CONFIG_SYS_LCRR_EADC LCRR_EADC_1
-#define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4
-#define CONFIG_SYS_LBC_LBCR (0x00040000 /* TODO */ \
- | (0xFF << LBCR_BMT_SHIFT) \
- | 0xF) /* 0x0004ff0f */
-
- /* LB refresh timer prescal, 266MHz/32 */
-#define CONFIG_SYS_LBC_MRTPR 0x20000000 /*TODO */
-
/* drivers/mtd/nand/nand.c */
#define CONFIG_SYS_NAND_BASE 0xE2800000
#define CONFIG_SYS_NAND_BLOCK_SIZE 16384
#define CONFIG_SYS_NAND_WINDOW_SIZE (32 * 1024)
-#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_NAND_BASE \
- | BR_DECC_CHK_GEN /* Use HW ECC */ \
- | BR_PS_8 /* 8 bit port */ \
- | BR_MS_FCM /* MSEL = FCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR1_PRELIM \
- (P2SZ_TO_AM(CONFIG_SYS_NAND_WINDOW_SIZE) \
- | OR_FCM_CSCT \
- | OR_FCM_CST \
- | OR_FCM_CHT \
- | OR_FCM_SCY_1 \
- | OR_FCM_TRLX \
- | OR_FCM_EHTR)
- /* 0xFFFF8396 */
-
/* Still needed for spl_minimal.c */
#define CONFIG_SYS_NAND_BR_PRELIM CONFIG_SYS_BR1_PRELIM
#define CONFIG_SYS_NAND_OR_PRELIM CONFIG_SYS_OR1_PRELIM
#define CONFIG_SYS_BCSR_ADDR 0xFA000000
#define CONFIG_SYS_BCSR_SIZE (32 * 1024) /* 0x00008000 */
/* map at 0xFA000000 on LCS3 */
-#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_BCSR_ADDR \
- | BR_PS_8 /* 8 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
- /* 0xFA000801 */
-#define CONFIG_SYS_OR3_PRELIM (OR_AM_32KB \
- | OR_GPCM_CSNT \
- | OR_GPCM_ACS_DIV2 \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xFFFF8FF7 */
/* Vitesse 7385 */
#ifdef CONFIG_VSC7385_ENET
#define CONFIG_SYS_VSC7385_BASE 0xF0000000
#define CONFIG_SYS_VSC7385_SIZE (128 * 1024) /* 0x00020000 */
-#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_VSC7385_BASE \
- | BR_PS_8 /* 8 bit port */ \
- | BR_MS_GPCM /* MSEL = GPCM */ \
- | BR_V) /* valid */
-#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB \
- | OR_GPCM_CSNT \
- | OR_GPCM_XACS \
- | OR_GPCM_SCY_15 \
- | OR_GPCM_SETA \
- | OR_GPCM_TRLX_SET \
- | OR_GPCM_EHTR_SET \
- | OR_GPCM_EAD)
- /* 0xFFFE09FF */
+
#endif
#define CONFIG_MPC83XX_GPIO 1
* Environment
*/
#if !defined(CONFIG_SYS_RAMBOOT)
- #define CONFIG_ENV_ADDR \
- (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
- #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */
- #define CONFIG_ENV_SIZE 0x2000
-
/* Address and size of Redundant Environment Sector */
-#else
- #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
- #define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_BOOTP_BOOTFILESIZE
/*
- * Command line configuration.
- */
-
-/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
/* Enable Internal USB Phy and GPIO on LCD Connector */
#define CONFIG_SYS_SICRL (SICRL_USBDR_10 | SICRL_LBC)
-#define CONFIG_SYS_HID0_INIT 0x000000000
-#define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \
- HID0_ENABLE_INSTRUCTION_CACHE | \
- HID0_ENABLE_DYNAMIC_POWER_MANAGMENT)
-
-#define CONFIG_SYS_HID2 HID2_HBE
-
/*
* Environment Configuration
*/
-#define CONFIG_ENV_OVERWRITE
#define CONFIG_NETDEV "eth1"
projects / platform / kernel / u-boot.git / blobdiff