#define CONFIG_PCI
#define CONFIG_83XX_GENERIC_PCI
+#define CONFIG_MISC_INIT_R
+
+/*
+ * On-board devices
+ *
+ * TSEC1 is VSC switch
+ * TSEC2 is SoC TSEC
+ */
+#define CONFIG_VSC7385_ENET
+#define CONFIG_TSEC2
+
#ifdef CFG_66MHZ
#define CONFIG_83XX_CLKIN 66666667 /* in Hz */
#elif defined(CFG_33MHZ)
#define CFG_ACR_RPTCNT 3 /* Arbiter repeat count (0-7) */
/*
+ * Device configurations
+ */
+
+/* Vitesse 7385 */
+
+#ifdef CONFIG_VSC7385_ENET
+
+#define CONFIG_TSEC1
+
+/* The flash address and size of the VSC7385 firmware image */
+#define CONFIG_VSC7385_IMAGE 0xFE7FE000
+#define CONFIG_VSC7385_IMAGE_SIZE 8192
+
+#endif
+
+/*
* DDR Setup
*/
#define CFG_DDR_BASE 0x00000000 /* DDR is system memory*/
* seem to have the SPD connected to I2C.
*/
#define CFG_DDR_SIZE 128 /* MB */
-#define CFG_DDR_CONFIG ( CSCONFIG_EN | CSCONFIG_AP \
- | 0x00040000 /* TODO */ \
+#define CFG_DDR_CONFIG ( CSCONFIG_EN \
+ | 0x00010000 /* TODO */ \
| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10 )
- /* 0x80840102 */
+ /* 0x80010102 */
#define CFG_DDR_TIMING_3 0x00000000
#define CFG_DDR_TIMING_0 ( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
/* 0x00220802 */
#define CFG_DDR_TIMING_1 ( ( 3 << TIMING_CFG1_PRETOACT_SHIFT ) \
- | ( 9 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
+ | ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
| ( 3 << TIMING_CFG1_ACTTORW_SHIFT ) \
| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
- | (13 << TIMING_CFG1_REFREC_SHIFT ) \
+ | (10 << TIMING_CFG1_REFREC_SHIFT ) \
| ( 3 << TIMING_CFG1_WRREC_SHIFT ) \
| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
- /* 0x3935d322 */
-#define CFG_DDR_TIMING_2 ( ( 0 << TIMING_CFG2_ADD_LAT_SHIFT ) \
- | (31 << TIMING_CFG2_CPO_SHIFT ) \
+ /* 0x3835a322 */
+#define CFG_DDR_TIMING_2 ( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+ | ( 5 << TIMING_CFG2_CPO_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
| ( 2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT ) \
| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
- | (10 << TIMING_CFG2_FOUR_ACT_SHIFT) )
- /* 0x0f9048ca */ /* P9-45,may need tuning */
-#define CFG_DDR_INTERVAL ( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
- | ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
- /* 0x03200064 */
+ | ( 6 << TIMING_CFG2_FOUR_ACT_SHIFT) )
+ /* 0x129048c6 */ /* P9-45,may need tuning */
+#define CFG_DDR_INTERVAL ( ( 1296 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+ | ( 1280 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
+ /* 0x05100500 */
#if defined(CONFIG_DDR_2T_TIMING)
#define CFG_SDRAM_CFG ( SDRAM_CFG_SREN \
| SDRAM_CFG_SDRAM_TYPE_DDR2 \
#endif
#define CFG_SDRAM_CFG2 0x00401000;
/* set burst length to 8 for 32-bit data path */
-#define CFG_DDR_MODE ( ( 0x4440 << SDRAM_MODE_ESD_SHIFT ) \
- | ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
- /* 0x44400232 */
+#define CFG_DDR_MODE ( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+ | ( 0x0632 << SDRAM_MODE_SD_SHIFT ) )
+ /* 0x44480632 */
#define CFG_DDR_MODE_2 0x8000C000;
#define CFG_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
/*
* Local Bus LCRR and LBCR regs
*/
-#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_2 /* 0x00010002 */
+#define CFG_LCRR LCRR_EADC_1 | LCRR_CLKDIV_4
#define CFG_LBC_LBCR ( 0x00040000 /* TODO */ \
| (0xFF << LBCR_BMT_SHIFT) \
| 0xF ) /* 0x0004ff0f */
-#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
+#define CFG_LBC_MRTPR 0x20000000 /*TODO */ /* LB refresh timer prescal, 266MHz/32 */
/* drivers/mtd/nand/nand.c */
#define CFG_NAND_BASE 0xE2800000 /* 0xF0000000 */
#define CFG_LBLAWBAR1_PRELIM CFG_NAND_BASE
#define CFG_LBLAWAR1_PRELIM 0x8000000E /* 32KB */
+/* local bus read write buffer mapping */
+#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
+#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
+#define CFG_LBLAWBAR3_PRELIM 0xFA000000
+#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+
+/* Vitesse 7385 */
+
#define CFG_VSC7385_BASE 0xF0000000
-#define CONFIG_VSC7385_ENET /* VSC7385 ethernet support */
+#ifdef CONFIG_VSC7385_ENET
+
#define CFG_BR2_PRELIM 0xf0000801 /* VSC7385 Base address */
#define CFG_OR2_PRELIM 0xfffe09ff /* VSC7385, 128K bytes*/
#define CFG_LBLAWBAR2_PRELIM CFG_VSC7385_BASE/* Access window base at VSC7385 base */
#define CFG_LBLAWAR2_PRELIM 0x80000010 /* Access window size 128K */
-/* local bus read write buffer mapping */
-#define CFG_BR3_PRELIM 0xFA000801 /* map at 0xFA000000 */
-#define CFG_OR3_PRELIM 0xFFFF8FF7 /* 32kB */
-#define CFG_LBLAWBAR3_PRELIM 0xFA000000
-#define CFG_LBLAWAR3_PRELIM 0x8000000E /* 32KB */
+#endif
/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT 1
#define CFG_I2C_OFFSET 0x3000
#define CFG_I2C2_OFFSET 0x3100
-/* TSEC */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
-#define CONFIG_NET_MULTI
-
/*
* General PCI
* Addresses are mapped 1-1.
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
/*
- * TSEC configuration
+ * TSEC
*/
#define CONFIG_TSEC_ENET /* TSEC ethernet support */
-#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
-#endif
-
-#define CONFIG_GMII 1 /* MII PHY management */
-#define CONFIG_TSEC1 1
+#define CONFIG_NET_MULTI
+#define CONFIG_GMII /* MII PHY management */
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC2 1
+#define CFG_TSEC1_OFFSET 0x24000
+#define TSEC1_PHY_ADDR 0x1c
+#define TSEC1_FLAGS TSEC_GIGABIT
+#define TSEC1_PHYIDX 0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC1_PHY_ADDR 0x1c
-#define TSEC2_PHY_ADDR 4
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
+#define CFG_TSEC2_OFFSET 0x25000
+#define TSEC2_PHY_ADDR 4
+#define TSEC2_FLAGS TSEC_GIGABIT
+#define TSEC2_PHYIDX 0
+#endif
+
/* Options are: TSEC[0-1] */
#define CONFIG_ETHPRIME "TSEC1"
#define CFG_HID2 HID2_HBE
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
+
/* DDR @ 0x00000000 */
#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10)
#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ETHADDR 00:E0:0C:00:95:01
-#define CONFIG_HAS_ETH1
-#define CONFIG_HAS_ETH0
#define CONFIG_ETH1ADDR 00:E0:0C:00:95:02
#define CONFIG_IPADDR 10.0.0.2
#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */
#define CONFIG_FDTFILE mpc8313erdb.dtb
-#define CONFIG_LOADADDR 200000 /* default location for tftp and bootm */
+#define CONFIG_LOADADDR 500000 /* default location for tftp and bootm */
#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */
#define CONFIG_BAUDRATE 115200
#define MK_STR(x) XMK_STR(x)
#define CONFIG_EXTRA_ENV_SETTINGS \
- "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
+ "netdev=" MK_STR(CONFIG_NETDEV) "\0" \
"ethprime=TSEC1\0" \
- "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
- "tftpflash=tftpboot $loadaddr $uboot; " \
- "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
- "erase " MK_STR(TEXT_BASE) " +$filesize; " \
- "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
- "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
- "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
+ "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot; " \
+ "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
+ "erase " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
+ "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
+ "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
"fdtaddr=400000\0" \
"fdtfile=" MK_STR(CONFIG_FDTFILE) "\0" \
"console=ttyS0\0" \
"setbootargs=setenv bootargs " \
"root=$rootdev rw console=$console,$baudrate $othbootargs\0" \
- "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
+ "setipargs=setenv bootargs nfsroot=$serverip:$rootpath " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
"root=$rootdev rw console=$console,$baudrate $othbootargs\0"
#define CONFIG_NFSBOOTCOMMAND \
"setenv rootdev /dev/nfs;" \
- "run setbootargs;" \
- "run setipargs;" \
+ "run setbootargs;" \
+ "run setipargs;" \
"tftp $loadaddr $bootfile;" \
"tftp $fdtaddr $fdtfile;" \
"bootm $loadaddr - $fdtaddr"
projects / platform / kernel / u-boot.git / blobdiff