#define CONFIG_4xx 1 /* ...member of PPC4xx family */
#define CONFIG_ML2 1 /* ...on a ML2 board */
+#define CONFIG_SYS_TEXT_BASE 0x18000000
+#define CONFIG_SYS_LDSCRIPT "board/ml2/u-boot.lds"
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_PREBOOT "fsload 0x00100000 /boot/image"
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#if 0
-#define CONFIG_SERIAL_SOFTWARE_FIFO 4000
-#else
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-#endif
-
#if 0
#define CONFIG_BOOTARGS "root=/dev/nfs " \
"ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 " \
#define CONFIG_CMD_JFFS2
#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
#undef CONFIG_CMD_RTC
#undef CONFIG_CMD_PCI
#undef CONFIG_CMD_I2C
#define CONFIG_SPD_EEPROM 1 /* use SPD EEPROM for setup */
/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_SPEED 400000
+
+/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x800000 /* inside of SDRAM */
-#define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
*/
#define SPD_EEPROM_ADDRESS 0x50
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
*
*/
/* No command line, one static partition, whole device */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#define CONFIG_JFFS2_PART_SIZE 0xFFFFFFFF
#define CONFIG_JFFS2_PART_OFFSET 0x00080000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nor0=ml2-0"
#define MTDPARTS_DEFAULT "mtdparts=ml2-0:-@512k(jffs2)"
*/