***********************************************************/
#define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
-/***********************************************************
- * Command definitions
- ***********************************************************/
-#define MIP405_COMMON_CMDS \
- (CONFIG_CMD_DFL | \
- CFG_CMD_CACHE | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_ELF | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_IRQ | \
- CFG_CMD_JFFS2 | \
- CFG_CMD_MII | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SAVES | \
- CFG_CMD_BSP )
-#if defined(CONFIG_MIP405T)
-#define CONFIG_COMMANDS \
- MIP405_COMMON_CMDS
-#else
-#define CONFIG_COMMANDS \
- (MIP405_COMMON_CMDS | \
- CFG_CMD_USB | \
- CFG_CMD_DOC )
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_BSP
+#if !defined(CONFIG_MIP405T)
+ #define CONFIG_CMD_USB
+ #define CONFIG_CMD_DOC
#endif
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+#define CONFIG_NAND_LEGACY
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
-#define CFG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET 0x00000 /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE 0x00800 /* 2k bytes may be used for env vars */
+#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
+#define CONFIG_ENV_OFFSET 0x00000 /* environment starts at the beginning of the EEPROM */
+#define CONFIG_ENV_SIZE 0x00800 /* 2k bytes may be used for env vars */
/***************************************************************
* Definitions for Serial Presence Detect EEPROM address
* (to get SDRAM settings)
***************************************************************/
/*#define SDRAM_EEPROM_WRITE_ADDRESS 0xA0
-#define SDRAM_EEPROM_READ_ADDRESS 0xA1
+#define SDRAM_EEPROM_READ_ADDRESS 0xA1
*/
/**************************************************************
* Environment definitions
#define CONFIG_BOOTDELAY 5
/* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
/* #define CONFIG_BOOT_RETRY_TIME -10 /XXX* feature is available but not enabled */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check console even if bootdelay = 0 */
#define CONFIG_BOOTCOMMAND "diskboot 400000 0:1; bootm" /* autoboot command */
#define CONFIG_BOOTARGS "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
**********************************************************/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
*/
/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CFG_DCACHE_SIZE 0x4000 /* For AMCC 405GPr CPUs */
-#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
-/*-----------------------------------------------------------------------
* Logbuffer Configuration
*/
-#undef CONFIG_LOGBUFFER /* supported but not enabled */
+#undef CONFIG_LOGBUFFER /* supported but not enabled */
/*-----------------------------------------------------------------------
* Bootcountlimit Configuration
*/
*/
#if 0 /* enable this if POST is desired (is supported but not enabled) */
#define CONFIG_POST (CFG_POST_MEMORY | \
- CFG_POST_CPU | \
- CFG_POST_RTC | \
+ CFG_POST_CPU | \
+ CFG_POST_RTC | \
CFG_POST_I2C)
#endif
#define PER_UART1_ADDR 0xF4200000 /* smallest window is 1MByte 0x10 0000*/
#define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
-#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
+#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
/*-----------------------------------------------------------------------
#define CFG_TEMP_STACK_OCM 1
#define CFG_OCM_DATA_ADDR 0xF0000000
#define CFG_OCM_DATA_SIZE 0x1000
-#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
+#define CFG_INIT_RAM_ADDR CFG_OCM_DATA_ADDR /* inside of On Chip SRAM */
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_ATA_IDE0_OFFSET 0x01F0 /* ide0 offste */
#define CFG_ATA_IDE1_OFFSET 0x0170 /* ide1 offset */
#define CFG_ATA_DATA_OFFSET 0 /* data reg offset */
-#define CFG_ATA_REG_OFFSET 0 /* reg offset */
+#define CFG_ATA_REG_OFFSET 0 /* reg offset */
#define CFG_ATA_ALT_OFFSET 0x200 /* alternate register offset */
#undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
/************************************************************
* Debug support
************************************************************/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
projects / platform / kernel / u-boot.git / blobdiff