* CONFIG_BOOT_PCI is only used for first boot-up and should
* NOT be enabled for production bootloader
***********************************************************/
-/*#define CONFIG_BOOT_PCI 1*/
+/*#define CONFIG_BOOT_PCI 1*/
/***********************************************************
* Clock
***********************************************************/
***********************************************************/
#define MIP405_COMMON_CMDS \
(CONFIG_CMD_DFL | \
- CFG_CMD_IDE | \
- CFG_CMD_DHCP | \
CFG_CMD_CACHE | \
- CFG_CMD_PCI | \
- CFG_CMD_IRQ | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
CFG_CMD_ECHO | \
CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_REGINFO | \
- CFG_CMD_DATE | \
CFG_CMD_ELF | \
+ CFG_CMD_FAT | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IDE | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_JFFS2 | \
CFG_CMD_MII | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
CFG_CMD_SAVES | \
CFG_CMD_BSP )
#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE CFG_FLASH_BASE
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc() */
/*
* For booting Linux, the board info and command line data
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1 /* ! second bank contains U-Boot */
+
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
+/*-----------------------------------------------------------------------
+ * Logbuffer Configuration
+ */
+#undef CONFIG_LOGBUFFER /* supported but not enabled */
+/*-----------------------------------------------------------------------
+ * Bootcountlimit Configuration
+ */
+#undef CONFIG_BOOTCOUNT_LIMIT /* supported but not enabled */
+
+/*-----------------------------------------------------------------------
+ * POST Configuration
+ */
+#if 0 /* enable this if POST is desired (is supported but not enabled) */
+#define CONFIG_POST (CFG_POST_MEMORY | \
+ CFG_POST_CPU | \
+ CFG_POST_RTC | \
+ CFG_POST_I2C)
+
+#endif
/*
* Init Memory Controller:
*/
+#define FLASH_MAX_SIZE 0x00800000 /* 8MByte max */
+#define FLASH_BASE_PRELIM 0xFF800000 /* open the flash CS */
+/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
+#define FLASH_SIZE_PRELIM 3 /* maximal flash FLASH size bank #0 */
-#define FLASH_BASE0_PRELIM 0xFFC00000 /* FLASH bank #0 */
-#define FLASH_BASE1_PRELIM 0 /* FLASH bank #1 */
-
-#define CONFIG_BOARD_PRE_INIT
+#define CONFIG_BOARD_EARLY_INIT_F 1
/* Peripheral Bus Mapping */
#define PER_PLD_ADDR 0xF4000000 /* smallest window is 1MByte 0x10 0000*/
#define CONFIG_PORT_ADDR PER_PLD_ADDR + 5
-
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in On Chip SRAM)
*/
#define CFG_INIT_RAM_END CFG_OCM_DATA_SIZE /* End of On Chip SRAM */
#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+/* reserve some memory for POST and BOOT limit info */
+#define CFG_INIT_SP_OFFSET (CFG_GBL_DATA_OFFSET - 32)
+
+#ifdef CONFIG_POST /* reserve one word for POST Info */
+#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 4)
+#endif
+
+#ifdef CONFIG_BOOTCOUNT_LIMIT /* reserve 2 word for bootcount limit */
+#define CFG_BOOTCOUNT_ADDR (CFG_GBL_DATA_OFFSET - 12)
+#endif
/*
* Internal Definitions
***********************************************************/
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-
+#define CONFIG_PHY_RESET_DELAY 300 /* Intel LXT971A needs this */
+#define CONFIG_PHY_CMD_DELAY 40 /* Intel LXT971A needs this */
/************************************************************
* RTC
***********************************************************/
#undef CONFIG_IDE_LED /* no led for ide supported */
#define CONFIG_IDE_RESET /* reset for ide supported... */
#define CONFIG_IDE_RESET_ROUTINE /* with a special reset function */
-
+#define CONFIG_SUPPORT_VFAT
/************************************************************
* ATAPI support (experimental)
************************************************************/
#define CONFIG_ATAPI /* enable ATAPI Support */
/************************************************************
- * SCSI support (experimental) only SYM53C8xx supported
- ************************************************************/
-#undef CONFIG_SCSI_SYM53C8XX
-
-#ifdef CONFIG_SCSI_SYM53C8XX
-#define CFG_SCSI_MAX_LUN 8 /* number of supported LUNs */
-#define CFG_SCSI_MAX_SCSI_ID 7 /* maximum SCSI ID (0..6) */
-#define CFG_SCSI_MAX_DEVICE CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN /* maximum Target devices */
-#define CFG_SCSI_SPIN_UP_TIME 2
-#endif /* CONFIG_SCSI_SYM53C8XX */
-/************************************************************
* DISK Partition support
************************************************************/
#define CONFIG_DOS_PARTITION
#endif
/************************************************************
+ * support BZIP2 compression
+ ************************************************************/
+#define CONFIG_BZIP2 1
+
+/************************************************************
* Ident
************************************************************/
projects / platform / kernel / u-boot.git / blobdiff