Makefile: move all Power Architecture boards into boards.cfg

[platform/kernel/u-boot.git] / include / configs / METROBOX.h

diff --git a/include/configs/METROBOX.h b/include/configs/METROBOX.h
index c0ddd45..04ae4f8 100644 (file)
--- a/include/configs/METROBOX.h
+++ b/include/configs/METROBOX.h
@@ -109,6 +109,9 @@
 #define CONFIG_BOARD_EARLY_INIT_F 1         /* Call board_pre_init     */
 #define CONFIG_MISC_INIT_F       1          /* Call board misc_init_f  */
 #define CONFIG_MISC_INIT_R       1          /* Call board misc_init_r  */
+
+#define        CONFIG_SYS_TEXT_BASE    0xFFF80000
+
 #undef CONFIG_SYS_DRAM_TEST                         /* Disable-takes long time!*/
 #define CONFIG_SYS_CLK_FREQ      66666666   /* external freq to pll    */
 
@@ -125,7 +128,6 @@
 #define CONFIG_SYS_FLASH_BASE         0xfff80000    /* start of FLASH          */
 #define CONFIG_SYS_MONITOR_BASE       0xfff80000    /* start of monitor        */
 #define CONFIG_SYS_PCI_MEMBASE        0x80000000    /* mapped pci memory       */
-#define CONFIG_SYS_PERIPHERAL_BASE    0xe0000000    /* internal peripherals    */
 #define CONFIG_SYS_ISRAM_BASE         0xc0000000    /* internal SRAM           */
 #define CONFIG_SYS_PCI_BASE           0xd0000000    /* internal PCI regs       */
 
@@ -144,8 +146,7 @@
 #define CONFIG_SYS_GBL_DATA_SIZE     128            /* num bytes initial data  */
 
 #define CONFIG_SYS_GBL_DATA_OFFSET   (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_POST_WORD_ADDR    (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
-#define CONFIG_SYS_INIT_SP_OFFSET    CONFIG_SYS_POST_WORD_ADDR
+#define CONFIG_SYS_INIT_SP_OFFSET    (CONFIG_SYS_GBL_DATA_OFFSET - 0x4)
 
 #define CONFIG_SYS_MONITOR_LEN       (256 * 1024)   /* Rsrv 256kB for Mon      */
 #define CONFIG_SYS_MALLOC_LEN        (128 * 1024)   /* Rsrv 128kB for malloc   */
@@ -153,7 +154,11 @@
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
+#define CONFIG_CONS_INDEX      1       /* Use UART0                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #define CONFIG_SERIAL_MULTI   1
 #define CONFIG_BAUDRATE              9600
 
@@ -194,6 +199,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C              1              /* I2C hardware support    */
 #undef CONFIG_SOFT_I2C                      /* I2C !bit-banged         */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #define CONFIG_SYS_I2C_SPEED         400000         /* I2C speed 400kHz        */
 #define CONFIG_SYS_I2C_SLAVE         0x7F           /* I2C slave address       */
 #define CONFIG_SYS_I2C_NOPROBES      {0x69}         /* Don't probe these addrs */
@@ -221,6 +227,7 @@
 /*-----------------------------------------------------------------------
  * Networking
  *----------------------------------------------------------------------*/
+#define CONFIG_PPC4xx_EMAC
 #define CONFIG_MII           1              /* MII PHY management      */
 #define CONFIG_NET_MULTI      1
 #define CONFIG_PHY_ADDR              0xff           /* no phy on EMAC0         */