* (easy to change)
*/
-#define CONFIG_SYS_UART_PORT (0)
-
-#define CONFIG_WATCHDOG_TIMEOUT 5000 /* timeout in milliseconds, max timeout is 6.71sec */
-
-#define CONFIG_SYS_UNIFY_CACHE
-
-#ifdef CONFIG_MCFFEC
-# define CONFIG_SYS_DISCOVER_PHY
-/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
-# ifndef CONFIG_SYS_DISCOVER_PHY
-# define FECDUPLEX FULL
-# define FECSPEED _100BASET
-# endif /* CONFIG_SYS_DISCOVER_PHY */
-#endif
+#define CFG_SYS_UART_PORT (0)
/* I2C */
-#ifdef CONFIG_MCFFEC
-# define CONFIG_IPADDR 192.162.1.2
-# define CONFIG_NETMASK 255.255.255.0
-# define CONFIG_SERVERIP 192.162.1.1
-# define CONFIG_GATEWAYIP 192.162.1.1
-#endif /* FEC_ENET */
-
-#define CONFIG_HOSTNAME "M5329EVB"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=40010000\0" \
"u-boot=u-boot.bin\0" \
"save\0" \
""
-#define CONFIG_PRAM 512 /* 512 KB */
+#define CFG_PRAM 512 /* 512 KB */
-#define CONFIG_SYS_CLK 80000000
-#define CONFIG_SYS_CPU_CLK CONFIG_SYS_CLK * 3
+#define CFG_SYS_CLK 80000000
+#define CFG_SYS_CPU_CLK CFG_SYS_CLK * 3
-#define CONFIG_SYS_MBAR 0xFC000000
+#define CFG_SYS_MBAR 0xFC000000
-#define CONFIG_SYS_LATCH_ADDR (CONFIG_SYS_CS1_BASE + 0x80000)
+#define CFG_SYS_LATCH_ADDR (CFG_SYS_CS1_BASE + 0x80000)
/*
* Low Level Configuration Settings
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */
-#define CONFIG_SYS_INIT_RAM_CTRL 0x221
-#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CFG_SYS_INIT_RAM_ADDR 0x80000000
+#define CFG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */
+#define CFG_SYS_INIT_RAM_CTRL 0x221
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CONFIG_SYS_SDRAM_BASE 0x40000000
-#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
-#define CONFIG_SYS_SDRAM_CFG1 0x53722730
-#define CONFIG_SYS_SDRAM_CFG2 0x56670000
-#define CONFIG_SYS_SDRAM_CTRL 0xE1092000
-#define CONFIG_SYS_SDRAM_EMOD 0x40010000
-#define CONFIG_SYS_SDRAM_MODE 0x018D0000
-
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-
-#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
+#define CFG_SYS_SDRAM_BASE 0x40000000
+#define CFG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
+#define CFG_SYS_SDRAM_CFG1 0x53722730
+#define CFG_SYS_SDRAM_CFG2 0x56670000
+#define CFG_SYS_SDRAM_CTRL 0xE1092000
+#define CFG_SYS_SDRAM_EMOD 0x40010000
+#define CFG_SYS_SDRAM_MODE 0x018D0000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
-#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
+#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + (CFG_SYS_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CONFIG_SYS_FLASH_CFI
-# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
-# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CFG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
#endif
-#ifdef CONFIG_NANDFLASH_SIZE
-# define CONFIG_SYS_MAX_NAND_DEVICE 1
-# define CONFIG_SYS_NAND_BASE CONFIG_SYS_CS2_BASE
-# define CONFIG_SYS_NAND_SIZE 1
-# define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#ifdef CONFIG_CMD_NAND
+# define CFG_SYS_NAND_BASE CFG_SYS_CS2_BASE
+# define CFG_SYS_NAND_BASE_LIST { CFG_SYS_NAND_BASE }
# define NAND_ALLOW_ERASE_ALL 1
#endif
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
+#define CFG_SYS_FLASH_BASE CFG_SYS_CS0_BASE
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
* Cache Configuration
*/
-#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
-#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
- CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 4)
+#define CFG_SYS_ICACHE_INV (CF_CACR_CINVA)
+#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \
+#define CFG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \
CF_CACR_DCM_P)
/*-----------------------------------------------------------------------
* CS4 - Available
* CS5 - Available
*/
-#define CONFIG_SYS_CS0_BASE 0
-#define CONFIG_SYS_CS0_MASK 0x007f0001
-#define CONFIG_SYS_CS0_CTRL 0x00001fa0
-
-#define CONFIG_SYS_CS1_BASE 0x10000000
-#define CONFIG_SYS_CS1_MASK 0x001f0001
-#define CONFIG_SYS_CS1_CTRL 0x002A3780
-
-#ifdef CONFIG_NANDFLASH_SIZE
-#define CONFIG_SYS_CS2_BASE 0x20000000
-#define CONFIG_SYS_CS2_MASK ((CONFIG_NANDFLASH_SIZE << 20) | 1)
-#define CONFIG_SYS_CS2_CTRL 0x00001f60
+#define CFG_SYS_CS0_BASE 0
+#define CFG_SYS_CS0_MASK 0x007f0001
+#define CFG_SYS_CS0_CTRL 0x00001fa0
+
+#define CFG_SYS_CS1_BASE 0x10000000
+#define CFG_SYS_CS1_MASK 0x001f0001
+#define CFG_SYS_CS1_CTRL 0x002A3780
+
+#ifdef CONFIG_CMD_NAND
+#define CFG_SYS_CS2_BASE 0x20000000
+#define CFG_SYS_CS2_MASK (16 << 20)
+#define CFG_SYS_CS2_CTRL 0x00001f60
#endif
+
#endif /* _M5329EVB_H */