* High Level Configuration Options
* (easy to change)
*/
-#define CONFIG_MCFTMR
-#define CONFIG_SYS_UART_PORT (0)
-
-#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */
+#define CFG_SYS_UART_PORT (0)
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
. = DEFINED(env_offset) ? env_offset : .; \
env/embedded.o(.text*);
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-#ifdef CONFIG_MCFFEC
-# define CONFIG_MII_INIT 1
-# define CONFIG_SYS_DISCOVER_PHY
-# define CONFIG_SYS_RX_ETH_BUFFER 8
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
-# ifndef CONFIG_SYS_DISCOVER_PHY
-# define FECDUPLEX FULL
-# define FECSPEED _100BASET
-# else
-# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-# endif
-# endif /* CONFIG_SYS_DISCOVER_PHY */
-#endif
-
-#ifdef CONFIG_MCFFEC
-# define CONFIG_IPADDR 192.162.1.2
-# define CONFIG_NETMASK 255.255.255.0
-# define CONFIG_SERVERIP 192.162.1.1
-# define CONFIG_GATEWAYIP 192.162.1.1
-#endif /* CONFIG_MCFFEC */
-
-#define CONFIG_HOSTNAME "M5282EVB"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"save\0" \
""
-#define CONFIG_SYS_CLK 64000000
+#define CFG_SYS_CLK 64000000
/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
-#define CONFIG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */
-#define CONFIG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */
+#define CFG_SYS_MFD 0x02 /* PLL Multiplication Factor Devider */
+#define CFG_SYS_RFD 0x00 /* PLL Reduce Frecuency Devider */
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
-#define CONFIG_SYS_MBAR 0x40000000
+#define CFG_SYS_MBAR 0x40000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+#define CFG_SYS_INIT_RAM_ADDR 0x20000000
+#define CFG_SYS_INIT_RAM_SIZE 0x10000 /* Size of used area in internal SRAM */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
-#define CONFIG_SYS_INT_FLASH_BASE 0xf0000000
-#define CONFIG_SYS_INT_FLASH_ENABLE 0x21
-
-/* If M5282 port is fully implemented the monitor base will be behind
- * the vector table. */
-#if (CONFIG_SYS_TEXT_BASE != CONFIG_SYS_INT_FLASH_BASE)
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
-#else
-#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x418) /* 24 Byte for CFM-Config */
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN 0x20000
-#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
+#define CFG_SYS_SDRAM_BASE 0x00000000
+#define CFG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
+#define CFG_SYS_FLASH_BASE CFG_SYS_CS0_BASE
+#define CFG_SYS_INT_FLASH_BASE 0xf0000000
+#define CFG_SYS_INT_FLASH_ENABLE 0x21
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + (CFG_SYS_SDRAM_SIZE << 20))
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CONFIG_SYS_FLASH_CFI
-# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
-# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
-# define CONFIG_SYS_FLASH_CHECKSUM
-# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
+# define CFG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
+# define CFG_SYS_FLASH_BANKS_LIST { CFG_SYS_FLASH_BASE }
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM)
-#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
- CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 4)
+#define CFG_SYS_ICACHE_INV (CF_CACR_CINV + CF_CACR_DCM)
+#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
+#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_DISD | \
CF_CACR_CEIB | CF_CACR_DBWE | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
-#define CONFIG_SYS_CS0_BASE 0xFFE00000
-#define CONFIG_SYS_CS0_CTRL 0x00001980
-#define CONFIG_SYS_CS0_MASK 0x001F0001
+#define CFG_SYS_CS0_BASE 0xFFE00000
+#define CFG_SYS_CS0_CTRL 0x00001980
+#define CFG_SYS_CS0_MASK 0x001F0001
/*-----------------------------------------------------------------------
* Port configuration
*/
-#define CONFIG_SYS_PACNT 0x0000000 /* Port A D[31:24] */
-#define CONFIG_SYS_PADDR 0x0000000
-#define CONFIG_SYS_PADAT 0x0000000
-
-#define CONFIG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */
-#define CONFIG_SYS_PBDDR 0x0000000
-#define CONFIG_SYS_PBDAT 0x0000000
-
-#define CONFIG_SYS_PCCNT 0x0000000 /* Port C D[15:08] */
-#define CONFIG_SYS_PCDDR 0x0000000
-#define CONFIG_SYS_PCDAT 0x0000000
-
-#define CONFIG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */
-#define CONFIG_SYS_PCDDR 0x0000000
-#define CONFIG_SYS_PCDAT 0x0000000
-
-#define CONFIG_SYS_PEHLPAR 0xC0
-#define CONFIG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */
-#define CONFIG_SYS_DDRUA 0x05
-#define CONFIG_SYS_PJPAR 0xFF
+#define CFG_SYS_PACNT 0x0000000 /* Port A D[31:24] */
+#define CFG_SYS_PADDR 0x0000000
+#define CFG_SYS_PADAT 0x0000000
+
+#define CFG_SYS_PBCNT 0x0000000 /* Port B D[23:16] */
+#define CFG_SYS_PBDDR 0x0000000
+#define CFG_SYS_PBDAT 0x0000000
+
+#define CFG_SYS_PDCNT 0x0000000 /* Port D D[07:00] */
+
+#define CFG_SYS_PEHLPAR 0xC0
+#define CFG_SYS_PUAPAR 0x0F /* UA0..UA3 = Uart 0 +1 */
+#define CFG_SYS_DDRUA 0x05
+#define CFG_SYS_PJPAR 0xFF
#endif /* _CONFIG_M5282EVB_H */