* (easy to change)
*/
-#define CONFIG_SYS_UART_PORT (0)
-
-#define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */
-
-#undef CONFIG_MONITOR_IS_IN_RAM /* define if monitor is started from a pre-loader */
+#define CFG_SYS_UART_PORT (0)
/* Configuration for environment
* Environment is embedded in u-boot in the second sector of the flash
. = DEFINED(env_offset) ? env_offset : .; \
env/embedded.o(.text);
-#ifdef CONFIG_MCFFEC
-# define CONFIG_IPADDR 192.162.1.2
-# define CONFIG_NETMASK 255.255.255.0
-# define CONFIG_SERVERIP 192.162.1.1
-# define CONFIG_GATEWAYIP 192.162.1.1
-#endif /* CONFIG_MCFFEC */
-
-#define CONFIG_HOSTNAME "M5272C3"
-#define CONFIG_EXTRA_ENV_SETTINGS \
+#define CFG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"loadaddr=10000\0" \
"u-boot=u-boot.bin\0" \
"save\0" \
""
-#define CONFIG_SYS_CLK 66000000
+#define CFG_SYS_CLK 66000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
-#define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */
-#define CONFIG_SYS_SCR 0x0003
-#define CONFIG_SYS_SPR 0xffff
+#define CFG_SYS_MBAR 0x10000000 /* Register Base Addrs */
+#define CFG_SYS_SCR 0x0003
+#define CFG_SYS_SPR 0xffff
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
+#define CFG_SYS_INIT_RAM_ADDR 0x20000000
+#define CFG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
+ * Please note that CFG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_SDRAM_SIZE 4 /* SDRAM size in MB */
-#define CONFIG_SYS_FLASH_BASE 0xffe00000
-
-#define CONFIG_SYS_MONITOR_LEN 0x20000
+#define CFG_SYS_SDRAM_BASE 0x00000000
+#define CFG_SYS_SDRAM_SIZE 4 /* SDRAM size in MB */
+#define CFG_SYS_FLASH_BASE 0xffe00000
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
-#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
+#define CFG_SYS_BOOTMAPSZ (CFG_SYS_SDRAM_BASE + (CFG_SYS_SDRAM_SIZE << 20))
/*
* FLASH organization
*/
#ifdef CONFIG_SYS_FLASH_CFI
-# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
-# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
+# define CFG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 8)
-#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - 4)
-#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
-#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
- CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
+#define ICACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 8)
+#define DCACHE_STATUS (CFG_SYS_INIT_RAM_ADDR + \
+ CFG_SYS_INIT_RAM_SIZE - 4)
+#define CFG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
+#define CFG_SYS_CACHE_ACR0 (CFG_SYS_SDRAM_BASE | \
+ CF_ADDRMASK(CFG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
-#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
+#define CFG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
CF_CACR_DISD | CF_CACR_INVI | \
CF_CACR_CEIB | CF_CACR_DCM | \
CF_CACR_EUSP)
/*-----------------------------------------------------------------------
* Port configuration
*/
-#define CONFIG_SYS_PACNT 0x00000000
-#define CONFIG_SYS_PADDR 0x0000
-#define CONFIG_SYS_PADAT 0x0000
-#define CONFIG_SYS_PBCNT 0x55554155 /* Ethernet/UART configuration */
-#define CONFIG_SYS_PBDDR 0x0000
-#define CONFIG_SYS_PBDAT 0x0000
-#define CONFIG_SYS_PDCNT 0x00000000
+#define CFG_SYS_PACNT 0x00000000
+#define CFG_SYS_PADDR 0x0000
+#define CFG_SYS_PADAT 0x0000
+#define CFG_SYS_PBCNT 0x55554155 /* Ethernet/UART configuration */
+#define CFG_SYS_PBDDR 0x0000
+#define CFG_SYS_PBDAT 0x0000
+#define CFG_SYS_PDCNT 0x00000000
#endif /* _M5272C3_H */