+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuation settings for the esd TASREG board.
*
* (C) Copyright 2004
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
*/
#define CONFIG_MCFTMR
-#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
-#undef CONFIG_WATCHDOG
-
#undef CONFIG_MONITOR_IS_IN_RAM /* no pre-loader required!!! ;-) */
/*
- * BOOTP options
- */
-#undef CONFIG_BOOTP_BOOTFILESIZE
-#undef CONFIG_BOOTP_BOOTPATH
-#undef CONFIG_BOOTP_GATEWAY
-#undef CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
-#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-
-#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */
-
-#define CONFIG_SYS_MEMTEST_START 0x400
-#define CONFIG_SYS_MEMTEST_END 0x380000
-
-/*
* Clock configuration: enable only one of the following options
*/
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_ENV_IS_IN_FLASH 1
-
#define LDS_BOARD_TEXT \
- . = DEFINED(env_offset) ? env_offset : .; \
- common/env_embedded.o (.text);
-
-#define CONFIG_ENV_OFFSET 0x4000 /* Address of Environment Sector*/
-#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE 0x2000 /* see README - env sector total size */
+ . = DEFINED(env_offset) ? env_offset : .; \
+ env/embedded.o(.text);
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#define CONFIG_SYS_MONITOR_LEN 0x20000
-#define CONFIG_SYS_MALLOC_LEN (1 * 1024*1024) /* Reserve 1 MB for malloc() */
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
/*
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
-# define CONFIG_FLASH_CFI_DRIVER 1
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
-# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
-# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CONFIG_SYS_FLASH_CHECKSUM
# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)