/*
- * (C) Copyright 2000, 2001, 2002
+ * (C) Copyright 2000-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
* Klaus Heydeck, Kieback & Peter GmbH & Co KG, heydeck@kieback-peter.de
*
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
#define CONFIG_MPC855 1 /* This is a MPC855 CPU */
#define CONFIG_KUP4K 1 /* ...on a KUP4K module */
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 9600 /* console baudrate */
+#define CONFIG_BAUDRATE 115200 /* console baudrate */
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
-#define CONFIG_BOOTDELAY 5 /* autoboot after 1 second */
+#define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */
#endif
-#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
-
#define CONFIG_BOARD_TYPES 1 /* support board types */
-#if 0
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
-#endif
#undef CONFIG_BOOTARGS
-#define CONFIG_NFSBOOTCOMMAND \
- "dhcp ;"\
- "setenv bootargs root=/dev/nfs ro nfsroot=$(nfsip):$(rootpath) "\
- "ip=$(ipaddr):$(nfsip):$(gatewayip):"\
- "$(netmask):heydeck.eva:eth0:off; "\
- "bootm 100000"
-#define CONFIG_RAMBOOTCOMMAND \
- "diskboot 100000 0:1; "\
- "setenv bootargs root=/dev/hda2 panic=1 "\
- "ip=192.168.0.71:192.168.0.100:192.168.0.2:255.255.255.0; "\
- "bootm"
-
-#define CONFIG_BOOTCOMMAND \
- "run ramboot "\
- "run nfsboot"
-
-#define CONFIG_MISC_INIT_R 1
+#define CONFIG_EXTRA_ENV_SETTINGS \
+"slot_a_boot=setenv bootargs root=/dev/hda2 ip=off;" \
+ "run addhw; diskboot 200000 0:1; bootm 200000\0" \
+"slot_b_boot=setenv bootargs root=/dev/hda2 ip=off;" \
+ "run addhw; diskboot 200000 2:1; bootm 200000\0" \
+"nfs_boot=dhcp; run nfsargs addip addhw; bootm 200000\0" \
+"panic_boot=echo No Bootdevice !!! reset\0" \
+"nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath}\0" \
+"ramargs=setenv bootargs root=/dev/ram rw\0" \
+"addip=setenv bootargs ${bootargs} ip=${ipaddr}:${serverip}:${gatewayip}" \
+ ":${netmask}:${hostname}:${netdev}:off\0" \
+"addhw=setenv bootargs ${bootargs} hw=${hw} key1=${key1} panic=1\0" \
+"netdev=eth0\0" \
+"contrast=55\0" \
+"silent=1\0" \
+"load=tftp 200000 bootloader-4k.bitmap;tftp 100000 bootloader-4k.bin\0" \
+"update=protect off 1:0-7;era 1:0-7;cp.b 100000 40000000 ${filesize};" \
+ "cp.b 200000 40050000 14000\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "run slot_a_boot;run slot_b_boot;run nfs_boot;run panic_boot"
+
+
+#define CONFIG_MISC_INIT_R 1
+#define CONFIG_MISC_INIT_F 1
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
+#define CONFIG_WATCHDOG 1 /* watchdog enabled */
-#define CONFIG_STATUS_LED 1 /* Status LED enabled */
+#define CONFIG_STATUS_LED 1 /* Status LED enabled */
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
-#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
+/*
+ * enable I2C and select the hardware/software driver
+ */
+#undef CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
+
+#define CFG_I2C_SPEED 93000 /* 93 kHz is supposed to work */
+#define CFG_I2C_SLAVE 0xFE
+
+#ifdef CONFIG_SOFT_I2C
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(2) /* 1/4 I2C clock duration */
+#endif /* CONFIG_SOFT_I2C */
+
+
+/*-----------------------------------------------------------------------
+ * I2C Configuration
+ */
+
+#define CFG_I2C_PICIO_ADDR 0x21 /* PCF8574 IO Expander */
+#define CFG_I2C_RTC_ADDR 0x51 /* PCF8563 RTC */
+
+
+/* List of I2C addresses to be verified by POST */
+
+#define I2C_ADDR_LIST {CFG_I2C_PICIO_ADDR, \
+ CFG_I2C_RTC_ADDR, \
+ }
+
+
+#define CONFIG_RTC_PCF8563 /* use Philips PCF8563 RTC */
+
+#define CFG_DISCOVER_PHY
+#define CONFIG_MII
+
+#if 0
#define CONFIG_ETHADDR 00:0B:64:00:00:00 /* our OUI from IEEE */
-#define CONFIG_KUP4K_LOGO 0x40040000 /* Address of logo bitmap */
+#endif
+#define CONFIG_KUP4K_LOGO 0x40050000 /* Address of logo bitmap */
/* Define to allow the user to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
+#if 1
+/* POST support */
+
+#define CONFIG_POST (CFG_POST_CPU | \
+ CFG_POST_RTC | \
+ CFG_POST_I2C)
+#endif
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
- CFG_CMD_IDE | \
- CFG_CMD_DATE )
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#ifdef CONFIG_POST
+ #define CONFIG_CMD_DIAG
+#endif
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+#define CFG_MEMTEST_START 0x000400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x002C00000 /* 4 ... 44 MB in DRAM */
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_LOAD_ADDR 0x200000 /* default load address */
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 115200 }
+
+#define CFG_CONSOLE_INFO_QUIET 1
/*
* Low Level Configuration Settings
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CFG_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0x40000000
-#define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#define CFG_MONITOR_BASE CFG_FLASH_BASE
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CFG_MAX_FLASH_SECT 19 /* max number of sectors on one chip */
#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
-#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
-#define CFG_ENV_SECT_SIZE 0x8000
+#define CFG_ENV_IS_IN_FLASH 1
+#define CFG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
+#define CFG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x10000
/* Address and size of Redundant Environment Sector */
#if 0
/*-----------------------------------------------------------------------
* Hardware Information Block
*/
-#if 0
-#define CFG_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
-#define CFG_HWINFO_SIZE 0x00000040 /* size of HW Info block */
-#define CFG_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
+#if 1
+#define CFG_HWINFO_OFFSET 0x000F0000 /* offset of HW Info block */
+#define CFG_HWINFO_SIZE 0x00000100 /* size of HW Info block */
+#define CFG_HWINFO_MAGIC 0x4B26500D /* 'K&P<CR>' */
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
-#if defined(CONFIG_WATCHDOG)
+#if 0 && defined(CONFIG_WATCHDOG) /* KUP uses external TPS3705 WD */
#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
*
* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
*/
-#define CFG_PLPRCR ( (3-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
+#define CFG_PLPRCR ( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
/*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
* power management and some other internal clocks
*/
#define SCCR_MASK SCCR_EBDF00
-#define CFG_SCCR ( SCCR_TBS | SCCR_EBDF00 | \
+#define CFG_SCCR (SCCR_TBS | SCCR_EBDF01 | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
*/
/* KUP4K use both slots, SLOT_A as "primary". */
-#define CONFIG_PCMCIA_SLOT_A 1
+#define CONFIG_PCMCIA_SLOT_A 1
#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
*-----------------------------------------------------------------------
*/
-#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
+#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
-#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
-#undef CONFIG_IDE_LED /* LED for ide not supported */
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#define CONFIG_IDE_LED 1 /* LED for ide supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CFG_IDE_MAXBUS 2
*-----------------------------------------------------------------------
*
*/
-/*#define CFG_DER 0x2002000F*/
-#define CFG_DER 0
+#define CFG_DER 0
/*
* Init Memory Controller:
#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
-/*
- * BR2/3 and OR2/3 (SDRAM)
- *
- */
-#define SDRAM_BASE1_PRELIM 0x00000000 /* SDRAM bank #0 */
-#define SDRAM_BASE2_PRELIM 0x20000000 /* SDRAM bank #1 */
-#define SDRAM_BASE3_PRELIM 0x30000000 /* SDRAM bank #2 */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 648 MB per bank */
-
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CFG_OR_TIMING_SDRAM 0x00000A00
-#if 0
-#define CFG_OR1_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-#define CFG_OR3_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_SDRAM )
-#define CFG_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#endif
-
/*
* Memory Periodic Timer Prescaler
* gclk CPU clock (not bus clock!)
* Trefresh Refresh cycle * 4 (four word bursts used)
*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
+ * 4096 Rows from SDRAM example configuration
+ * 1000 factor s -> ms
+ * 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
+ * 4 Number of refresh cycles per period
+ * 64 Refresh cycle in ms per number of rows
* --------------------------------------------
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
*
*
* Boot Flags
*/
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if NOT_USED_FOR_NOW
#define CONFIG_AUTOBOOT_KEYED /* use key strings to stop autoboot */
#if 0
-#define CONFIG_AUTOBOOT_PROMPT "Boote in %d Sekunden - stop mit \"2\"\n"
+#define CONFIG_AUTOBOOT_PROMPT \
+ "Boote in %d Sekunden - stop mit \"2\"\n", bootdelay
#endif
-#define CONFIG_AUTOBOOT_STOP_STR "2" /* easy to stop for now */
-#endif /* NOT_USED_FOR_NOW */
+#define CONFIG_AUTOBOOT_STOP_STR "." /* easy to stop for now */
+#define CONFIG_SILENT_CONSOLE 1
#endif /* __CONFIG_H */