/* JSE has a PPC405GPr */
#define CONFIG_405GP 1
/* ... which is a 4xxx series */
-#define CONFIG_4xx 1
+#define CONFIG_4x 1
/* ... with a 33MHz OSC. connected to the SysCLK input */
#define CONFIG_SYS_CLK_FREQ 33333333
/* ... with on-chip memory here (4KBytes) */
/* Do not set up locked dcache as init ram. */
#undef CONFIG_SYS_INIT_DCACHE_CS
+#define CONFIG_SYS_TEXT_BASE 0xFFF80000
+
/* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */
#define CONFIG_SYSTEMACE 1
#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
/* ... place INIT RAM in the OCM address */
# define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR
/* ... give it the whole init ram */
-# define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE
+# define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE
/* ... Shave a bit off the end for global data */
-# define CONFIG_SYS_GBL_DATA_SIZE 128
-# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+# define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
/* ... and place the stack pointer at the top of what's left. */
# define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_ENV_OFFSET 0x00
#define CONFIG_ENV_SIZE 512
-
/* The JSE connects UART1 to the console tap connector. */
-#define CONFIG_UART1_CONSOLE 1
+#define CONFIG_CONS_INDEX 2
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_serial_clock()
+
/* Set console baudrate to 9600 */
#define CONFIG_BAUDRATE 9600
-/* Size (bytes) of interrupt driven serial port buffer.
- * Set to 0 to use polling instead of interrupts.
- * Setting to 0 will also disable RTS/CTS handshaking.
- */
-#undef CONFIG_SERIAL_SOFTWARE_FIFO
-
/*
* Configuration related to auto-boot.
*
#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address */
-#define CONFIG_NET_MULTI
/*
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-#endif
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
/* Configuration Port location */
#define CONFIG_PORT_ADDR 0xF0000500
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */