#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
+#define CONFIG_HIGH_BATS 1 /* High BATs supported */
/*
* Serial console configuration
#if defined(CONFIG_PCI)
#define CONFIG_PCI_PNP 1
#define CONFIG_PCI_SCAN_SHOW 1
+#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_PCI_MEM_BUS 0x40000000
#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
#define CONFIG_PCI_IO_BUS 0x50000000
#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
#define CONFIG_PCI_IO_SIZE 0x01000000
-#define ADD_PCI_CMD CFG_CMD_PCI
#endif
#define CFG_XLB_PIPELINING 1
#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
#define CONFIG_NS8382X 1
-#else /* MPC5100 */
-
+#else
#define CONFIG_MII 1
-#define ADD_PCI_CMD 0 /* no CFG_CMD_PCI */
-
#endif
/* Partitions */
#define CONFIG_ISO_PARTITION
/* USB */
-#if 1
-#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
+#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
-#endif
+#define CFG_OHCI_BE_CONTROLLER
+#undef CFG_USB_OHCI_BOARD_INIT
+#define CFG_USB_OHCI_CPU_INIT 1
+#define CFG_USB_OHCI_REGS_BASE MPC5XXX_USB
+#define CFG_USB_OHCI_SLOT_NAME "mpc5200"
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_IDE | \
- CFG_CMD_NFS | \
- CFG_CMD_SNTP | \
- ADD_PCI_CMD | \
- ADD_USB_CMD )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
+
+#if defined(CONFIG_PCI)
+#define CONFIG_CMD_PCI
+#endif
+
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CFG_LOWBOOT 1
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_PREBOOT "echo;" \
- "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
* IPB Bus clocking configuration.
*/
#if defined(CONFIG_LITE5200B)
-#define CFG_IPBSPEED_133 /* define for 133MHz speed */
+#define CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#else
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
#endif
#endif /* CONFIG_MPC5200 */
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+
+#define OF_CPU "PowerPC,5200@0"
+#define OF_SOC "soc5200@f0000000"
+#define OF_TBCLK (bd->bi_busfreq / 4)
+#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
+
/*
* I2C configuration
*/
#undef CONFIG_FLASH_16BIT /* Flash is 8-bit */
#if defined(CONFIG_LITE5200B)
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_BANKS_LIST {CFG_CS1_START,CFG_CS0_START}
#endif
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/