#define CONFIG_MPC860T 1
#define CONFIG_MPC862 1
+#define CONFIG_SYS_TEXT_BASE 0x08000000
+
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#undef CONFIG_8xx_CONS_SMC1
# define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
-#define CONFIG_PREBOOT "echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
/* using this define saves us updating another source file */
-#define CONFIG_BOARD_PRE_INIT 1
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_MISC_INIT_R
#undef CONFIG_BOOTARGS
/* #define CONFIG_BOOTCOMMAND \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;" \
- "bootm"
+ "bootp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
+ "bootm"
*/
#define CONFIG_BOOTCOMMAND \
- "setenv bootargs root=/dev/nfs" \
- "ip=192.168.28.129:139.10.137.138:192.168.28.1:255.255.255.0:iadlinux002::off; " \
+ "setenv bootargs root=/dev/nfs" \
+ "ip=192.168.28.129:139.10.137.138:192.168.28.1:255.255.255.0:iadlinux002::off; " \
#undef CONFIG_WATCHDOG /* watchdog disabled */
/* #define CONFIG_STATUS_LED 1*/ /* Status LED enabled */
-#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+
# undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */
# define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-# define CFG_DISCOVER_PHY 1
+# define CONFIG_MII 1
+# define CONFIG_SYS_DISCOVER_PHY 1
# define CONFIG_FEC_UTOPIA 1
# define CONFIG_ETHADDR 08:00:06:26:A2:6D
# define CONFIG_IPADDR 192.168.28.128
# define CONFIG_SERVERIP 139.10.137.138
-# define CFG_DISCOVER_PHY 1
+# define CONFIG_SYS_DISCOVER_PHY 1
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
/* enable I2C and select the hardware/software driver */
#undef CONFIG_HARD_I2C /* I2C with hardware support */
#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-# define CFG_I2C_SPEED 50000
-# define CFG_I2C_SLAVE 0xDD
-# define CFG_I2C_EEPROM_ADDR 0x50
+# define CONFIG_SYS_I2C_SPEED 50000
+# define CONFIG_SYS_I2C_SLAVE 0xDD
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
/*
* Software (bit-bang) I2C driver configuration
*/
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
-#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DHCP | \
- CFG_CMD_DATE )
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DATE
+
/*
* Miscellaneous configurable options
*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CFG_MEMTEST_START 0x0100000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
+#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-#define CFG_LOAD_ADDR 0x00100000
+#define CONFIG_SYS_LOAD_ADDR 0x00100000
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
-#define CFG_IMMR 0xFFF00000
-#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+#define CONFIG_SYS_IMMR 0xFFF00000
+#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
-#define CFG_INIT_RAM_ADDR CFG_IMMR
-#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
-#define CFG_SDRAM_BASE 0x00000000
-#define CFG_FLASH_BASE 0x08000000
-#define CFG_FLASH_SIZE ((uint)(4 * 1024 * 1024)) /* max 16Mbyte */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_FLASH_BASE 0x08000000
+#define CONFIG_SYS_FLASH_SIZE ((uint)(4 * 1024 * 1024)) /* max 16Mbyte */
-#define CFG_RESET_ADDRESS 0xFFF00100
+#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
#if defined(DEBUG)
-# define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
+# define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
-# define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
+# define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
-# define CFG_MONITOR_BASE CFG_FLASH_BASE
-# define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+# define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+# define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
-#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_OFFSET 0x8000
-#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x8000
+#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
/*-----------------------------------------------------------------------
* Cache Configuration
*/
-#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
-#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
-#define CFG_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
-#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
-#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* set the PLL, the low-power modes and the reset control (15-29)
*/
-#define CFG_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
+#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \
PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
/*-----------------------------------------------------------------------
*/
#define SCCR_MASK SCCR_EBDF11
-#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
+#define CONFIG_SYS_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
SCCR_DFLCD000 |SCCR_DFALCD00 )
*-----------------------------------------------------------------------
*/
/* +0x09C4 => DRQP = 10 (IDMA requests have lowest priority) */
-#define CFG_RCCR 0x0020
+#define CONFIG_SYS_RCCR 0x0020
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*
*/
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
/* Because of the way the 860 starts up and assigns CS0 the
* entire address space, we have to set the memory controller
* BR0 and OR0 (FLASH)
*/
-#define FLASH_BASE0_PRELIM CFG_FLASH_BASE /* FLASH bank #0 */
+#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
-#define CFG_REMAP_OR_AM 0xF8000000 /* OR addr mask */
-#define CFG_PRELIM_OR_AM 0xF8000000 /* OR addr mask */
+#define CONFIG_SYS_REMAP_OR_AM 0xF8000000 /* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM 0xF8000000 /* OR addr mask */
/* FLASH timing:
TRLX = 0, CSNT = 1, SCY = 3, EHTR = 1 */
-#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | \
+#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | \
OR_SCY_3_CLK | OR_EHTR)
-#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
/*
* BR2/3 and OR2/3 (SDRAM)
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
-#define CFG_OR2_PRELIM (CFG_PRELIM_OR_AM | OR_CSNT_SAM | OR_BI | OR_ACS_DIV4)
-#define CFG_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-#define CFG_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
+#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | OR_CSNT_SAM | OR_BI | OR_ACS_DIV4)
+#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
+#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE1_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
/*
* Memory Periodic Timer Prescaler
*/
/* periodic timer for refresh */
-#define CFG_MAMR_PTA 124 /* start with divider for 64 MHz */
+#define CONFIG_SYS_MAMR_PTA 124 /* start with divider for 64 MHz */
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CFG_MPTPR MPTPR_PTP_DIV32 /* setting for 1 bank */
+#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV32 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
-#define CFG_MAMR ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+#define CONFIG_SYS_MAMR ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_8X)
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
#ifdef CONFIG_MPC860T
/* Interrupt level assignments.