* (C) Copyright 2005
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
+ * (C) Copyright 2006
+ * Matthias Fuchs, esd GmbH, matthias.fuchs@esd-electronics.com
+ *
* See file CREDITS for list of people who contributed to this
* project.
*
#define CONFIG_PREBOOT "autoupd"
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "pciconfighost=1\0" \
+ ""
+
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+#define CONFIG_NET_MULTI 1
+#undef CONFIG_HAS_ETH1
+
#define CONFIG_MII 1 /* MII PHY management */
-#define CONFIG_PHY_ADDR 0 /* PHY address */
+#define CONFIG_PHY_ADDR 0 /* PHY address */
#define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
#define CONFIG_PHY_CLK_FREQ EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
/*
* Video console
*/
-#define CONFIG_VIDEO
+#define CONFIG_VIDEO /* for sm501 video support */
+
+#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_SM501
#if 0
#define CONFIG_VIDEO_SM501_32BPP
#else
#define CONFIG_VIDEO_SM501_16BPP
#endif
+#define CONFIG_VIDEO_SM501_FBMEM_OFFSET 0x10000
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CFG_CONSOLE_IS_IN_ENV
#define CONFIG_SPLASH_SCREEN
#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
-#define CFG_VIDEO_LOGO_MAX_SIZE (1024*1024) /* for decompressed img */
+#define CFG_VIDEO_LOGO_MAX_SIZE (2 << 20) /* for decompressed img */
-#ifdef CONFIG_VIDEO
#define ADD_BMP_CMD CFG_CMD_BMP
#else
#define ADD_BMP_CMD 0
-#endif
+#endif /* CONFIG_VIDEO */
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
CFG_CMD_DHCP | \
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
+#define CFG_NAND_LEGACY
+
#undef CONFIG_BZIP2 /* include support for bzip2 compressed images */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CFG_FLASH_BASE 0xFFF80000
#define CFG_MONITOR_BASE TEXT_BASE
#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Monitor */
-#define CFG_MALLOC_LEN (2 * 1024*1024) /* Reserve 2 MB for malloc() */
+#define CFG_MALLOC_LEN (4 << 20) /* Reserve 4 MB for malloc() */
#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
# define CFG_RAMBOOT 1
#define CFG_LCD_SMALL_MEM 0xF1400000 /* Epson S1D13704 Mem Base Address */
#define CFG_LCD_SMALL_REG 0xF140FFE0 /* Epson S1D13704 Reg Base Address */
-#define CFG_LCD_LOGO_MAX_SIZE (1024*1024)
-
/*-----------------------------------------------------------------------
* Universal Interrupt Controller (UIC) Setup
*/
#define CFG_FPGA_CTRL_VGA0_BL_MODE 0x0008
#define CFG_FPGA_CTRL_CF_RESET 0x0040
#define CFG_FPGA_CTRL_PS2_PWR 0x0080
-#define CFG_FPGA_CTRL_CF_PWR 0x0100 /* low active */
+#define CFG_FPGA_CTRL_CF_PWRN 0x0100 /* low active */
#define CFG_FPGA_CTRL_CF_BUS_EN 0x0200
#define CFG_FPGA_CTRL_LCD_CLK 0x7000 /* Mask for lcd clock */
+#define CFG_FPGA_CTRL_OW_ENABLE 0x8000
+
+#define CFG_FPGA_STATUS_CF_DETECT 0x8000
#define LCD_CLK_OFF 0x0000 /* Off */
#define LCD_CLK_02083 0x1000 /* 2.083 MHz */