Makefile: move all Power Architecture boards into boards.cfg

[platform/kernel/u-boot.git] / include / configs / HH405.h

diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index ed9a235..661db2b 100644 (file)
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -43,6 +43,8 @@
 #define CONFIG_4xx             1       /* ...member of PPC4xx family   */
 #define CONFIG_HH405           1       /* ...on a HH405 board          */
 
+#define        CONFIG_SYS_TEXT_BASE    0xFFF80000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* call board_early_init_f()    */
 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
 
@@ -176,9 +178,14 @@
 #define CONFIG_SYS_MEMTEST_START       0x0400000       /* memtest works on     */
 #define CONFIG_SYS_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM  */
 
+#define CONFIG_CONS_INDEX      2       /* Use UART1                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
+
 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* no external serial clock used */
 #define CONFIG_SYS_BASE_BAUD       691200
-#define CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
 
 /* The following table includes the supported baudrates */
 #define CONFIG_SYS_BAUDRATE_TABLE      \
@@ -306,7 +313,7 @@
  */
 #define CONFIG_SYS_SDRAM_BASE          0x00000000
 #define CONFIG_SYS_FLASH_BASE          0xFFF80000
-#define CONFIG_SYS_MONITOR_BASE        TEXT_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_MONITOR_LEN         (512 * 1024)    /* Reserve 512 kB for Monitor   */
 #define CONFIG_SYS_MALLOC_LEN          (4 << 20)       /* Reserve 4 MB for malloc()    */
 
@@ -331,6 +338,7 @@
  * I2C EEPROM (CAT24WC16) for environment
  */
 #define CONFIG_HARD_I2C                        /* I2c with hardware support */
+#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
 #if 0 /* test-only */
 #define CONFIG_SYS_I2C_SPEED           400000  /* I2C speed and slave address */
 #else
@@ -413,23 +421,6 @@
 
 #define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100       /* FPGA internal Base Address       */
 
-/* FPGA internal regs */
-#define CONFIG_SYS_FPGA_CTRL           0x000
-
-/* FPGA Control Reg */
-#define CONFIG_SYS_FPGA_CTRL_REV0      0x0001
-#define CONFIG_SYS_FPGA_CTRL_REV1      0x0002
-#define CONFIG_SYS_FPGA_CTRL_VGA0_BL   0x0004
-#define CONFIG_SYS_FPGA_CTRL_VGA0_BL_MODE 0x0008
-#define CONFIG_SYS_FPGA_CTRL_CF_RESET  0x0040
-#define CONFIG_SYS_FPGA_CTRL_PS2_PWR   0x0080
-#define CONFIG_SYS_FPGA_CTRL_CF_PWRN   0x0100      /* low active                    */
-#define CONFIG_SYS_FPGA_CTRL_CF_BUS_EN 0x0200
-#define CONFIG_SYS_FPGA_CTRL_LCD_CLK   0x7000      /* Mask for lcd clock            */
-#define CONFIG_SYS_FPGA_CTRL_OW_ENABLE 0x8000
-
-#define CONFIG_SYS_FPGA_STATUS_CF_DETECT 0x8000
-
 #define LCD_CLK_OFF             0x0000      /* Off                           */
 #define LCD_CLK_02083           0x1000      /* 2.083 MHz                     */
 #define LCD_CLK_03135           0x2000      /* 3.135 MHz                     */
@@ -477,12 +468,12 @@
  * GPIO0[28-29] - UART1 data signal input/output
  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
  */
-#define CONFIG_SYS_GPIO0_OSRH          0x40000550
-#define CONFIG_SYS_GPIO0_OSRL          0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H         0x00000000
-#define CONFIG_SYS_GPIO0_ISR1L         0x15555440
-#define CONFIG_SYS_GPIO0_TSRH          0x00000000
+#define CONFIG_SYS_GPIO0_OSRL          0x40000550
+#define CONFIG_SYS_GPIO0_OSRH          0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L         0x00000000
+#define CONFIG_SYS_GPIO0_ISR1H         0x15555440
 #define CONFIG_SYS_GPIO0_TSRL          0x00000000
+#define CONFIG_SYS_GPIO0_TSRH          0x00000000
 #define CONFIG_SYS_GPIO0_TCR           0xF7FE0017
 
 #define CONFIG_SYS_LCD_ENDIAN          (0x80000000 >> 7)