i2c, ppc4xx_i2c: switch to new multibus/multiadapter support

[platform/kernel/u-boot.git] / include / configs / CMS700.h

diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 9c57acb..ca258e6 100644 (file)
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -37,6 +37,8 @@
 #define CONFIG_4xx             1       /* ...member of PPC4xx family   */
 #define CONFIG_VOM405          1       /* ...on a VOM405 board         */
 
+#define        CONFIG_SYS_TEXT_BASE    0xFFFC8000
+
 #define CONFIG_BOARD_EARLY_INIT_F 1    /* call board_early_init_f()    */
 #define CONFIG_MISC_INIT_R     1       /* call misc_init_r()           */
 
@@ -53,7 +55,6 @@
 #define CONFIG_SYS_LOADS_BAUD_CHANGE   1       /* allow baudrate change        */
 
 #define CONFIG_PPC4xx_EMAC
-#define CONFIG_NET_MULTI       1
 #undef  CONFIG_HAS_ETH1
 
 #define CONFIG_MII             1       /* MII PHY management           */
@@ -102,9 +103,6 @@
 #define CONFIG_SYS_PROMPT      "=> "           /* Monitor Command Prompt       */
 
 #undef CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */
-#ifdef CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE      1024            /* Console I/O Buffer Size      */
@@ -207,8 +205,8 @@
  */
 #define CONFIG_SYS_SDRAM_BASE          0x00000000
 #define CONFIG_SYS_FLASH_BASE          CONFIG_SYS_MONITOR_BASE
-#define CONFIG_SYS_MONITOR_BASE                TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN         (~(TEXT_BASE) + 1)
+#define CONFIG_SYS_MONITOR_BASE                CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN         (~(CONFIG_SYS_TEXT_BASE) + 1)
 #define CONFIG_SYS_MALLOC_LEN          (256 * 1024)
 
 #if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
@@ -228,10 +226,11 @@
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
-#define CONFIG_HARD_I2C                        /* I2c with hardware support */
-#define CONFIG_PPC4XX_I2C              /* use PPC4xx driver            */
-#define CONFIG_SYS_I2C_SPEED           100000  /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE           0x7F
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0          100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0          0x7F
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50    /* EEPROM CAT28WC08             */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1       /* Bytes of address             */
@@ -284,10 +283,9 @@
 #define CONFIG_SYS_OCM_DATA_ADDR       0xF8000000
 #define CONFIG_SYS_OCM_DATA_SIZE       0x1000
 #define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM             */
-#define CONFIG_SYS_INIT_RAM_END        CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM     */
+#define CONFIG_SYS_INIT_RAM_SIZE       CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM    */
 
-#define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -318,14 +316,6 @@
 #define CONFIG_SYS_PLD_RESET           (0x80000000 >> 12)   /* GPIO12 */
 
 /*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01            /* Normal Power-On: Boot from FLASH     */
-#define BOOTFLAG_WARM  0x02            /* Software reboot                      */
-
-/*
  * Default speed selection (cpu_plb_opb_ebc) in mhz.
  * This value will be set if iic boot eprom is disabled.
  */