ppc4xx: Use common NS16550 driver for PPC4xx UART

[platform/kernel/u-boot.git] / include / configs / CATcenter.h

diff --git a/include/configs/CATcenter.h b/include/configs/CATcenter.h
index a44f3e1..550c462 100644 (file)
--- a/include/configs/CATcenter.h
+++ b/include/configs/CATcenter.h
@@ -86,7 +86,11 @@
 # error "* External frequency (SysClk) not defined! *"
 #endif
 
-#define CONFIG_UART1_CONSOLE   1       /* Use second UART              */
+#define CONFIG_CONS_INDEX      2       /* Use UART1                    */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK         get_serial_clock()
 #define CONFIG_BAUDRATE                115200
 #define CONFIG_BOOTDELAY       5       /* autoboot after 5 seconds     */
 
@@ -184,7 +188,6 @@
 #define CONFIG_SYS_MEMTEST_END         0x0C00000       /* 4 ... 12 MB in DRAM  */
 
 #undef CONFIG_SYS_EXT_SERIAL_CLOCK             /* no external serial clock used */
-#define CONFIG_SYS_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
 #define CONFIG_SYS_BASE_BAUD           691200
 
 /* The following table includes the supported baudrates */
@@ -210,17 +213,8 @@
 
 /* For CATcenter there is only NAND on the module */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
-#define SECTORSIZE 512
 #define NAND_NO_RB
 
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN    0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
 #define CONFIG_SYS_NAND0_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
 #define CONFIG_SYS_NAND0_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
 #define CONFIG_SYS_NAND0_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
@@ -545,13 +539,13 @@
  * GPIO0[30]   - EMAC0 input
  * GPIO0[31]   - EMAC1 reject packet as output
  */
-#define CONFIG_SYS_GPIO0_OSRH          0x40000550
-#define CONFIG_SYS_GPIO0_OSRL          0x00000110
-#define CONFIG_SYS_GPIO0_ISR1H         0x00000000
-/*#define CONFIG_SYS_GPIO0_ISR1L       0x15555445*/
-#define CONFIG_SYS_GPIO0_ISR1L         0x15555444
-#define CONFIG_SYS_GPIO0_TSRH          0x00000000
+#define CONFIG_SYS_GPIO0_OSRL          0x40000550
+#define CONFIG_SYS_GPIO0_OSRH          0x00000110
+#define CONFIG_SYS_GPIO0_ISR1L         0x00000000
+/*#define CONFIG_SYS_GPIO0_ISR1H       0x15555445*/
+#define CONFIG_SYS_GPIO0_ISR1H         0x15555444
 #define CONFIG_SYS_GPIO0_TSRL          0x00000000
+#define CONFIG_SYS_GPIO0_TSRH          0x00000000
 #define CONFIG_SYS_GPIO0_TCR           0xF7FF8014
 
 /*
@@ -783,7 +777,7 @@
  *
  */
 /* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
+#undef CONFIG_CMD_MTDPARTS
 #define CONFIG_JFFS2_DEV               "nand"
 #define CONFIG_JFFS2_PART_SIZE         0x00200000
 #define CONFIG_JFFS2_PART_OFFSET       0x00000000
@@ -793,7 +787,7 @@
  * Note: fake mtd_id used, no linux mtd map file
  */
 /*
-#define CONFIG_JFFS2_CMDLINE
+#define CONFIG_CMD_MTDPARTS
 #define MTDIDS_DEFAULT         "nand0=catcenter"
 #define MTDPARTS_DEFAULT       "mtdparts=catcenter:2m(nand)"
 */