+/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2011-2012 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier: GPL-2.0+
*/
/*
#ifndef __CONFIG_H
#define __CONFIG_H
-#ifdef CONFIG_BSC9131RDB
-#define CONFIG_BSC9131
#define CONFIG_NAND_FSL_IFC
-#endif
#ifdef CONFIG_SPIFLASH
#define CONFIG_RAMBOOT_SPIFLASH
#define CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_SYS_TEXT_BASE 0x11000000
#define CONFIG_RESET_VECTOR_ADDRESS 0x110bfffc
#endif
#define CONFIG_SPL_FLUSH_IMAGE
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
-#define CONFIG_SYS_TEXT_BASE 0x00201000
#define CONFIG_SPL_TEXT_BASE 0xFFFFE000
#define CONFIG_SPL_MAX_SIZE 8192
#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000
#endif
/* High Level Configuration Options */
-#define CONFIG_BOOKE /* BOOKE */
-#define CONFIG_E500 /* BOOKE e500 family */
-#define CONFIG_FSL_IFC /* Enable IFC Support */
-#define CONFIG_FSL_CAAM /* Enable SEC/CAAM */
-#define CONFIG_FSL_LAW /* Use common FSL init code */
-#define CONFIG_TSEC_ENET
#define CONFIG_ENV_OVERWRITE
#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */
#define CONFIG_SYS_MEMTEST_END 0x01ffffff
/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR3
#undef CONFIG_SYS_DDR_RAW_TIMING
#undef CONFIG_DDR_SPD
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_NUM_DDR_CONTROLLERS 1
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
#define CONFIG_CHIP_SELECTS_PER_CTRL 1
/*
* IFC Definitions
*/
-#define CONFIG_SYS_NO_FLASH
/* NAND Flash on IFC */
#define CONFIG_SYS_NAND_BASE 0xff800000
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_DDR_LAW 11
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
-#define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */
-
#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* End of used area in RAM */
#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc*/
/* Serial Port */
-#define CONFIG_CONS_INDEX 1
#undef CONFIG_SERIAL_SOFTWARE_FIFO
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_NS16550_MIN_FUNCTIONS
#endif
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
-
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
/* I2C EEPROM */
-#define CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* eSPI - Enhanced SPI */
-#ifdef CONFIG_FSL_ESPI
-#define CONFIG_SF_DEFAULT_SPEED 10000000
-#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
-#endif
#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_MII /* MII PHY management */
#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
#define CONFIG_TSEC1 1
#define CONFIG_TSEC1_NAME "eTSEC1"
#define CONFIG_ETHPRIME "eTSEC1"
-#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
-
#endif /* CONFIG_TSEC_ENET */
/*
* Environment
*/
#if defined(CONFIG_RAMBOOT_SPIFLASH)
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS 0
-#define CONFIG_ENV_SPI_CS 0
-#define CONFIG_ENV_SPI_MAX_HZ 10000000
-#define CONFIG_ENV_SPI_MODE 0
#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_SIZE 0x2000
#elif defined(CONFIG_NAND)
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_SYS_EXTRA_ENV_RELOC
#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE
#define CONFIG_ENV_OFFSET ((768 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE)
#elif defined(CONFIG_SYS_RAMBOOT)
-#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
#define CONFIG_ENV_SIZE 0x2000
#endif
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * Command line configuration.
- */
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_IRQ
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_REGINFO
-
-/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
#if defined(CONFIG_CMD_KGDB)
#else
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
- /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
/*
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
-/* Hash command with SHA acceleration supported in hardware */
-#ifdef CONFIG_FSL_CAAM
-#define CONFIG_CMD_HASH
-#define CONFIG_SHA_HW_ACCEL
-#endif
-
-#define CONFIG_USB_EHCI
-
-#ifdef CONFIG_USB_EHCI
+#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
/*
* Dynamic MTD Partition support with mtdparts
*/
-#define CONFIG_MTD_DEVICE
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nand0=ff800000.flash,"
-#define MTDPARTS_DEFAULT "mtdparts=ff800000.flash:1m(uboot)," \
- "8m(kernel),512k(dtb),-(fs)"
-/*
- * Override partitions in device tree using info
- * in "mtdparts" environment variable
- */
-#ifdef CONFIG_CMD_MTDPARTS
-#define CONFIG_FDT_FIXUP_PARTITIONS
-#endif
/*
* Environment Configuration
#define CONFIG_HAS_ETH0
#endif
-#define CONFIG_HOSTNAME BSC9131rdb
+#define CONFIG_HOSTNAME "BSC9131rdb"
#define CONFIG_ROOTPATH "/opt/nfsroot"
#define CONFIG_BOOTFILE "uImage"
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
-#define CONFIG_BAUDRATE 115200
-
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot=" CONFIG_UBOOTPATH "\0" \
projects / platform / kernel / u-boot.git / blobdiff